The water tank shown below is being filledthrough section 1 at u₁ =3 m/s and throughsection 3 at Q3 = 0.016 m³/s. If water levelh is constant and d1=5 cm, d2= 4 cm,determine the volumetric flowrate Q2.d1образ03m^3/sWaterOTEd2

Answered: Image /qna-images/answer/7400f9f8-cfc6-4210-8fe4-274ac69a2798.jpg

The water tank shown below is being filled through section 1 at U1 =3 m/s and through section 3 at Q3 = 0.016 m3/s. If water level h is constant and d1=5 cm, d2= 4 cm, determine the volumetric flowrate Q2. 에 d1 어, 03 m^3/s Water d2

The water tank shown below is being filled through section 1 at U1 =3 m/s and through section 3 at Q3 = 0.016 m3/s. If water level h is constant and d1=5 cm, d2= 4 cm, determine the volumetric flowrate Q2. 에 d1 어, 03 m^3/s Water d2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The water of a 14’ × 48’ metal frame pool can drain from the pool through an opening at the side of the pool. The opening is about h = 1.05 m below the water level. The capacity of the pool is V = 3740 gallons, the pool can be drained in t = 10.2 mins. P0 is the pressure of the atmosphere. ρ is the density of the water. a. Write the Bernoulli’s equation of the water at the top of the pool in terms of P0, ρ, h. Assuming the opening is the origin. b. Write the Bernoulli’s equation of the water at the opening of the pool in terms of P0, ρ, h and v, where v is the speed at which the water leaves the opening. Assuming the opening is the origin. c. Express v2 in terms of g and h. d. Calculate the numerical value of v in meters per second. e. Express the flow rate of the water in terms of V and t. f. Express the cross-sectional area of the opening, A, in terms of V, v and t. g. Calculate the numerical value of A in cm2
Q2) Oil flows through a pipe as shown in fig2. The coefficient of discharge for the orifice in the pipe is C.-0,63. What is the discharge of oil in the pipe? P1-P2 P1-P2 V22-V₁² Let: -4.48. Y 100-mm-diameter, sharp-edged orifice (2) 250mm 6.958 Heavy oil
answer fast
The figure shows a channel with width of 2.4 m. The density of the water is 1000 kg/m^3. The flow is steady. At the entrance of the channel, the flow is uniform with velocity V (m/s) while at the exit, the flow has developed the shown velocity profile u(y) = 4y-2y^2 (m/s) and y is in (m). Answer the following questions. The area in (m^2) of the entrance is: V 0.75 u = 4y – 2y? The area in m^2 at the exit section is: The average velocity in (m/s) at the exit section is:
= Water flows into a tank and out through another pipe, as shown in the figure below. The water in the tank has a surface area, Asur f 5.6 m². At the bottom of the tank there is a door inclined at an angle = 25 degrees with respect to the horizontal. The door has a length L = 1.1 m and a width w=1 m (out of the page). The flowrate into the tank is Q₁ (t) flowrate out is Qo(t) = 0.05 m³/s At time t = Asurf = 0.26 m³/s and the 0, the water has a depth ho = 2.5 m. The density of water is p = 1000 kg/m³. Ө h(t) Qout
The figure below shows a gasoline storage tank with cross-sectional area Asub1, filled to a depth h. The space above the gasoline contains air at pressure psub0, and the gasoline flows out the bottom of the tank through a short pipe with cross-sectional area Asub2. Derive expressions for the flow speed in the pipe and the volume flow rate. Thank you!
Current Attempt in Progress The pump shown in the figure below delivers a head of 250 ft to the water. Determine the power that the pump adds to the water. The difference in elevation of the two ponds is 150 ft. Assume L= 200 ft, D=0.5 ft. - 1.0 Pump K - 1.5 ebow - 5.0 Pipe length - L Pipe diameter -D Pipe roughness -0 = 0.৪ ft-lb/s or i hp
An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a constant cross sectional area of 0.40 m². It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Using c=0.60, which of the following most nearly gives the head in meter after 240 seconds from an initial head of 1.20m?
Please solve this problem, thank you
Water flows at the rate of 0.015 m/sec from open reservoir A to open reservoir B (both are large reservoirs that are open to the atmosphere) through two concrete (8 = 0.32 mm) pipes connected in series. If L1 = 800 m, Di = 16 cm, L2 = 200 m, and D2 = 8 cm, determine the difference in water surface elevations (Az) of the reservoirs. The coefficient of contraction (K.) is 0.36, the entrance coefficient is K = 0.5, the exit coefficient is K = 1.0, and assume fully turbulent flow (Xx = 9810 N/m?, Ku = 1.12 x 10-6 m²/s). You do not need to check if the assumption of fully turbulent flow is valid, just assume that it is valid. А Az =? Pipe 1 В Pipe 2 undefined
*83. Go Two hoses are connected to the same outlet using a Y-connector, as the drawing shows. The hoses A and B have the same length, but hose B has the larger radius. Each is open to the atmosphere at the end where the water exits. Water flows through both hoses as a viscous fluid, and Poiseuille's law [Q = ™R°(P2 – P)/(8nL)] applies to each. In this law, , P, is the pressure upstream, P, is the pressure downstream, and Q is the volume flow rate. The ratio of the radius of hose B to the radius of hose A is Rg/RA = 1.50. Find the ratio of the speed of the water in hose B to the speed in hose A. Water from outlet Hose A Hose B Problem 83
Q2- Water density =1000 kg/m and viscosity is 0.001 Ns/m², is pumped between two reservoirs at 0.2m/s through a 400 m of 8 cm diameter Cast Iron pipe and several minor losses as shown in the figure. Compute the pump power required in kW. Use the last one digit of your ID number for Z1 level in meter. Screwed Z2= 50 m regular 90° elbow Sharp exit Z;= ID m Sharp entrance Half-open gate valve `bend radius Pump Open globe valve 8 cm diameter