The Water Environment Federation (WEF) recommends that the linear flow-through velocity in a wastewater clarifier should be less than to 0.020 m/s to prevent scour. Using ẞ = 0.06 for sticky particles and a Darcy-Weisback friction factor of 0.03, estimate the specific gravity of a 200 μm diameter particle that will be scoured at the recommended velocity. Express your answer in kg/m³ and round to the nearest integer.

The Water Environment Federation (WEF) recommends that the linear flow-through velocity in a wastewater clarifier should be less than to 0.020 m/s to prevent scour. Using ẞ = 0.06 for sticky particles and a Darcy-Weisback friction factor of 0.03, estimate the specific gravity of a 200 μm diameter particle that will be scoured at the recommended velocity. Express your answer in kg/m³ and round to the nearest integer.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter2: Origin Of Soil And Grain Size

Section: Chapter Questions

Problem 2.14P: A hydrometer test has the following result: Gs = 2.65, temperature of water = 26 C, and L = 10.4 cm...

See similar textbooks

Similar questions

Refer to Problem 2.C.1. Results of the sieve analysis for Soils A, B, and C are given below. To obtain a more representative sample for further geotechnical testing, a ternary blend is created by uniformly mixing 8000 kg of each soil. Answer the following questions. a. If a sieve analysis is conducted on the mixture using the same set of sieves as shown above, compute the mass retained (as a percentage) and cumulative percent passing in each sieve. b. What would be the uniformity coefficient (Cu) and the coefficient of gradation (Cc) of the mixture?
Repeat Problem 2.14 with the following values: Gs = 2.75, temperature of water = 21C, t = 88 min, and L = 11.7 cm. 2.14 A hydrometer test has the following result: Gs = 2.65, temperature of water = 26 C, and L = 10.4 cm at 45 minutes after the start of sedimentation (see Figure 2.25). What is the diameter D of the smallest-size particles that have settled beyond the zone of measurement at that time (that is, t = 45 min)? Figure 2.25 ASTM 152H type of hydrometer placed inside the sedimentation cylinder (Courtesy of Khaled Sobhan, Florida Atlantic University, Boca Raton, Florida)
Repeat Problem 2.8 using the following data. 2.8 The following are the results of a sieve and hydrometer analysis. a. Draw the grain-size distribution curve. b. Determine the percentages of gravel, sand, silt and clay according to the MIT system. c. Repeat Part b according to the USDA system. d. Repeat Part b according to the AASHTO system.
Refer to Figure 7.24. The following data were collected during the field permeability measurement of a confined aquifer using a pumping test. Determine the hydraulic conductivity of the permeable layer. Use Eq. (7.49). Thickness of the aquifer, H = 4.5 m Piezometric level and radial distance of the first observation well: h1 = 2.9 m; r1 = 17.8 m Piezometric level and radial distance of the second observation well: h2 = 1.8 m; r2 = 8.1 m Rate of discharge from pumping, q = 0.5 m3/min
A sand has Gs = 2.66. Calculate the hydraulic gradient that will cause boiling for e = 0.35, 0.45, 0.55, 0.7, and 0.8.
The following data were obtained by conducting liquid limit and plastic limit tests on a soil collected from the site. Liquid limit tests: Plastic limit test: PL = 19.3% a. Draw the flow curve and determine the liquid limit. b. Using the Casagrande plasticity chart (Figure 4.21), determine the soil type.