The wall is 2.5 m high and consists of 51mm x 102mm studs plastered on one side. On the other side is 13 mm fiberboard and 102 mm clay brick. Determine the average load in kN/m length of the wall that the wall exerts on the floor. From NSCP 2015 Table 204-2: . 51mm x 102mm studs plastered on one side - 0.57 kPa 13 mm fiberboard -0.38 kPa 102 mm clay bricks -1.87 kPa

The wall is 2.5 m high and consists of 51mm x 102mm studs plastered on one side. On the other side is 13 mm fiberboard and 102 mm clay brick. Determine the average load in kN/m length of the wall that the wall exerts on the floor. From NSCP 2015 Table 204-2: . 51mm x 102mm studs plastered on one side - 0.57 kPa 13 mm fiberboard -0.38 kPa 102 mm clay bricks -1.87 kPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A timber wall 75 mm wide, 75 mm deep and 3.50 m high is assumed to be fixed at the top and bottom. It is subjected to uniformly distributed load of 388 N/m acting along the weaker axis of its entire height. The wall is made up of Apitong wood with 80% stress grade with properties as shown: Bending and tension parallel to the grain = 16.5 MPa Modulus of Elasticity in Bending = 7310 MPa Compression parallel to the grain = 9.56 MPa Compression perpendicular to the grain = 2.20 MPa Compute for the following: a) Allowable compressive stress b) Allowable bending stress c) Maximum axial load %3D %3D %3D
QI/ Choose the Correct Answer? 1. Queen closer may be placed A. In header course B. In stretcher course E In any position. C In header course next to first brick D In stretcher course next to first brick 2. The foundations are placed below ground level, to increase A. Strength B. Workability C. Stability of structure D. All the above. 3. The 11 cm x 7.5 cm side of a brick as seen in the wall face, is generally known as: A. Stretcher C. Face Е. Неader в. Front D. Side 4. Buildings can be classified according to construction Method to: A. cast in situ and Pre cast B. Nonstructural Buildings C. Lightweight structures 5. The Ribbed Slabs are known: B. Short Span A. Long Span C. Intermediate span
Provide correct answer Thanks for the help Determine maximum principal stress
Q: In an attempt to construct a precast building, the architectural in engineer proposed a 400 mm width for a simply supported single reinforced concrete rectangular beam. Design this beam and assume your design that: fc = 25 MPa, fy = 400 MPa, L = 6 m, D.L = 160 kN/m (include self-weight), L.L = 150 kN/m, concrete weight = 24 kN/m3, bar diameter of 25 mm for longitudinal reinforcement and bar diameters 10 mm for stirrups.
ll中国移动 4G PN © 11:50 PM 75% 4 A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial compressive strength of the concrete is f. - 14.3 N/ mm. The longitudinal steel bars are 6 22 with the yield strength ofS, - 360 N/mm. The spirals are 10@50 with the yield strength of f,- 270 N/ mm². If the concrete cover is 30 mm thick, determine the ultimate compressive capacity of the column.
A floor panel 3 4 m wide and 12 m long is intended for a vibratory machine in a factory. The concrete to be used has a strength of 27.6 MPa (whose density is 1800 kg per cubic meter) and reinforcement used has yield strength of 280 MPa Determine the minimum thickness of slab if the panel is cantilever
A concrete wall is 4m high, 6m long, and 4 in thick. Determine the number of 4kg. cement, sand and gravel required using concrete class AA.
If the elastic sag of the concrete member was 3 cm for the corresponding continuous load, what is the final total sag in consideration of additional long-term sag due to creep and dry contraction? (However, the load loading period is 10 years, and the compression reinforcement ratio p′=0.005)
Design the reinforced concrete wall shown if fc’ = 2100 psi and fy = 40000 psi
Determine the losses in the post-tensioned concrete beam as shown below. 560 mm Given: POST-TENSIONED BEAM with A PARABOLIC TENDON PROFILE Span Length = 20 m fi = 1200 N/mm² A, = 2850 mm² Ac 4.23x105 mm² 1=9.36x10¹0 mm e-560 mm (@midspan, from N.A.) fc= 40 N/mm² Es = 210,000 N/mm² μ = 0.19 K = 0.0005 (per meter) Anchorage slip = 5 mm (jacked at left-end only). (make sure to draw the force variation diagram for anchorage slip) V/S= 6 RH = 70 Dead Load 9.97 kN/m fpy = 1714 N/mm² Bridge Width III
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛