The volume solved using end area method is equal to 245 cubic meters, after using prismoidal correction, a volume correction of -4 cubic meters was determined. What is the real volume?

Q: 20. The X and Y coordinates of five stations of travese are given in the accompanying tabulation a…

A:

Q: A ring is formed by rotating the area 360° about the x̄ – x̄ axes. Determine its volume.

A: Volume = area*length

Q: The answer in the book is a=1.67 m

A: From the given question, we have to find out the value of 'a' to consider the same amount of…

Q: A truncated right prism has an equilateral triangular base with one side measures 3 cm. The lateral…

A:

Q: Problem #2: 50 + A (N) A 35 ° 9. Determine the reaction at point A.(N) 10. Determine the reaction at…

A:

Q: A block of steel ( s.g. = 7.85 ) will "float" at a mercury-water interface as %3D shown in the…

A: Answer = 238.26 mm

Q: rmine R in N at point C.

A: 200kg=2009.81=1962N20lbf=204.448=88.964N

Q: 5. Determine the v-component of F1. (N) 6. Determine the u-component of F1. (N)

A:

Q: B 30° 8. Determine the reaction at B. (Ib) 9. Determine the horizontal reaction at A. (Ib) 10.…

A:

Q: B Y (N/m) 30° 0.75 m Y (N-m) - 1.5 m 1. Determine the resultant force of the triangular loading. (N)…

A: Given data,  Y = 25 To find out the resultant of triangular loading, reaction in A and B

Q: PROBLEM 7: Locate the center of mass of the block in millimeters. Materials 1, 2 and 3 have…

A:

Q: 7. The base of a spherical pyramid is a spherical triangle whos angles are 85°, 115°, and 90°. If…

A:

Q: Solve and determine INAX , INAY, and Area total. Show complete solution.

A:

Q: . Compute the midspan value of El8 for the beam shown in Fig. P-653. (Hint: Draw the M diagram by…

A:

Q: The point P in the figure travels on the parabola (with focal distance f = 0.5 m) at the constant…

A: Given that  The equation of the path is 2y = x2 The value of the focal distance is f = 0.5 m The…

Q: A simple beam of 10 mm x 40 inm steel (Es = 200GPA) plate sandwiched by two 5 mm x 40 mm brass…

A: we know…

Q: Determine the volume and the surface area of the half-torus shown in the figure. R

A: Given half torus:

Q: Problem 2.5. A metallic bar 300 mm x 100 mm x 40 mm is subjected to a force of 5 kN (tensile), 6 kN…

A: Given : Metallic bar section - 300 mm X 100 mm X 40 mm Tensile force = 5 kN , 6 kN and 4 kN along x…

Q: Solve for one possible solution in the equation, using Secant Method (cosx/e^-x)+sinx-e^x+x

A:

Q: Determine the surface area of the ring. The cross section is circular as shown.

A:

Q: For the element shown below, radius of Mohr circle is? Ox dy oy 0x o₂=110 N/mm², o, 30 N/mm² and…

A: Given- State of stress- σx=110 N/mm2,σy=30 N/mm2,τxy=30 N/mm2, It is needed to find the radius of…

Q: Problem #4: В C D Blocks A, B, and C have weights of YN, 25 N, and 15 N, respectively. The…

A:

Q: How can water displacement be used to measure the density of a non-porous irregularly shaped solid?

A:

Q: Determine the z-coordinate of the centroid of the rectangular solid with the hemispherical hole. The…

A:

Q: Determine the volume of solid obtained by rotating the region bounded by y = x^2 - 2x and y = x…

A: Step: 1 Curve: - It is a continuous line which gradually deviates without any sharp turns. For…

Q: SHOW COMPLETE SOLUTION PLS VALUE: Y =25

A: To find reaction at support A and B

Q: 28.30mm 28.20mm чомра 6-A 20mm by 20mm square is etched onto a metal bar prior to loading. Upon…

A: To find Poisson ratio and Young's modulus

Q: A tensile load of 50 kN is acting on rod of 50 mm diameter and length of 5 m. Determine the length…

A: Given that, both AB and BC are subjected to 50Kn.

Q: Q 3:Determine the center of gravity of the object formed by the combination of homogeneous blocks…

A: please find attached solution below.

Q: Calculate the volume V of the solid generated by revolving the 65-mm right-triangular area about the…

A:

Q: SHOW COMPLETE SOLUTION PLS VALUES: A = 5 C = 1

A: A=5 C=1 To find tension in cable AB,AC,AD

Q: 4 m E 4 m 24 kN B 4 m 12 kN C (b) Assume that the two loads acting on the truss above have been…

A:

Q: Problem #4: 45+ A (degrees) B D Mass of Cylinder = Y (kg) In order to maintain equilibrium, 18.…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.