The vertical shear force acting on the l-section shown is 100 kN. 20 mm 160 mm 20 mm 20 mm - 120 mm - Compute the percentage of the shear force carried by the web. 78.63 98.9 100 90.2

Q: An earth dam require a total of 150 cubic meter of soll compacted with a bulk unit weight of 18.5 kN…

A:

Q: I. Determine the rotation at point A and the deflection at the free end using moment diagram by…

A:

Q: A conical draft-tube having diameter at the top as 2.0 m and pressure head at 7 m of water (vacuum),…

A:

Q: A beam is limited to the dimensions b = 15 in, d = 20 in,. and d' = 4 in. If Mp = 170 kip-ft…

A: We have to determine the value of limiting steel ratio maximum steel area based on steel ratio and…

Q: A column is supported on a footing as shown in the figure below. The water table is at a depth of 10…

A: Given- Water table at a depth of 10 m, Size of footing- 1.5 m × 3 m, Depth of footing Df=1 m, Unit…

Q: Show that the vectors ( A=3i+ 6j) and ( B=-i-2j) have opposite direction

A:

Q: Liquid is flowing in a pipeline 60 mm in diameter at 9.5 cu. m. per hour. If the density of fluid is…

A:

Q: 13- How many bbl does a 8000ft of 5x4 (OD-ID) drill pipes displace?

A: Given h = 8000ft Outer dia = 5ft  Inner dia= 4ft

Q: 6. Determine the resultant moment about point A of the system of forces shown below. Each square is…

A:

Q: QUESTION 1 An element in plane stress is subjected to stresses; Ox, Oy, and Txy (FIGURE 1). Using…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: The hydraulic conductivity, k of a soil is 7.15 x10-°cm/s at a temperature of 20° C. Determine its…

A:

Q: i Given the four points A (1, -1), B (2, 0), C (-1, 3) and D (-2, 2) Find the vectors AB and CD and…

A:

Q: Determine the forces in the members by using the method of section and inspection. 120 AN 120 AN 120…

A: The method of sections is generally a process helped to determine the unknown forces acting on…

Q: 1. From the given cross section of the proposed barangay road. The road base is 6m and the side…

A: Consider the given data.

Q: A 160-lb box is held at rest on a smooth surface (9 = 19°) inclined by a force, 'P' making an angle…

A: This question is related to the Engineering Mechanics from Civil Engineering. In this problem we…

Q: A pump with 400 mm diameter suction and a 350 mm diameter discharge pipe is to deliver 20,000 liters…

A:

Q: The rectangular channel has a width of 8 ft and transports water at 18(103) ft³ /min. Suppose that…

A: Given :Width (B) = 8 ftDischarge (Q) = 18×103 ft3/min= 18×10360 = 300 ft3/secDepth at section 1 (y1)…

Q: Example21 A vibrating system of mass 20 kg and spring with stiffness 32 N/mm is viscosity damped so…

A:

Q: Calculate the limiting length (m) of the offset, if the maximum allowable error in laying offset is…

A: given- maximum allowable error=2oscale of map= 1 cm = 100 m

Q: The force F has a magnitude of 710 N. Express F as a vector in terms of the unit vectors i and j.…

A:

Q: Determine the maximum deflection in region AB of the overhang beam. Take E = 29(103)kst and I =…

A:

Q: Member (1) has an area of 2300 mm? and an allowable normal stress of 110 MPa. Member (2) has an area…

A: Lami's theorem: when three forces acting on the body where the forces are coplanar and concurrent,…

Q: Question 24- At a certain point in the floor of weir, the uplift pressure head due to seepage is 5.4…

A:

Q: The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a…

A: Longitudinal Stress is the vessel has closed ends the internal pressure acts on them to develop a…

Q: The end of the boom O is subjected to three concurrent and coplanar forces. Determine the magnitude…

A: Schematic diagram of the given problem:

Q: Determine the ultimate moment capacity of a reinforced concrete T-beam with the following…

A:

Q: 4. The truss shown carries the given loads. Determine the magnitude of the resultant, its…

A: Truss structure is a connection of at least three or more members which are used to support roof in…

Q: Find the force in member HG and specify if it is in tension or compression? HG = 4 kN 3 kN 2 kN E 3…

A:

Q: Eaves, canopies, awnings (or media agua) over uired windows shall not be less than 740 millimeters n…

A: Since you have asked multiple question, we will solve first 3 questions for you. To get remaining…

Q: Use the virtual work method to determine the slope and deflection at point D of the beam shown. -15…

A:

Q: Material Strengths: Fy = 248 MPa, Fu= 400 MPa The channel (C200X17.1) is connected with four M16…

A:

Q: 6. A cubic tank is completely filled with water. What will be the ratio of the hydrostatic force…

A: To find: Ratio of hydrostatic force exerted on base and on any of the vertical sides

Q: 2. USE CONJUGATE BEAM METHOD. For the beam shown, determine the following: a. Slope at point A in…

A:

Q: Determine the Deflection at the midspan of AB in inches unit. Use the Double Integration Method.…

A: This method entails obtaining the deflection of a beam by integrating the differential equation of…

Q: A soil sample having a void ratio of 1.3, water content of 50% and a specific gravity of 2.60, is in…

A:

Q: 2. Use the virtual work method to determine the horizontal deflections at joint C of the frame…

A:

Q: A city has a population of 50000 people and they consume an average 20 million m3 of natural gas per…

A: Question is based on the solid waste management data.Population of city,average consumption of…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.