The velocity of pin C relative to the slot is 26 in/s upward and is decreasing at 50in/s². Part A What is the angular velocity of bar AC? (Figure 1) Express your answer with the appropriate units. rad WAC = 3.71 B Submit Previous Answers Part B Correct What is the angular acceleration of bar AC? Express your answer with the appropriate units. με ? gure 1 of 1 rad AC= Value 7 in BO 4 in Submit Previous Answers Request Answer X Incorrect; Try Again Provide Feedback

Q: What information did the Hodgkin and Huxley model provide?

A: It helps to have some background on what happens during an action potential to understand Hodgkin…

Q: Time between job arrivals at a machining station is exponentially distributed with mean 4.4 minutes.…

A: Given:To find:Simulate the system for one 8-hour day.

Q: Which of the following can be used to building up a three-dimensional prototype model layer by layer…

A: According to the given data We need to find Following can be used to building up a three-dimensional…

Q: A die forge press operates an average of 1000 hr/yr. Under a minimal repair concept, machine…

A:

Q: Datum features must be specified in a feature control frame in order of: O Numerical order O…

A: Datum features must be specified in a feature control frame in order of precedence.  Answer - C

Q: The last 3 compartments in a feature control frame provides the datum references; this is known as…

A: The last 3 feature control frame provides the datum referances, this is known as datum order of…

Q: The diameters of the main rotor and tail rotor of a single engine helicopter are 7.51 m and 1.01 m,…

A: Diameter of main rotor, Diameter of tail rotor, Rotational speed of main rotor, Rotational speed of…

Q: Geometric Dimensioning and Tolerancing was designed to insure the proper assembly of Geometric…

A: All questions are solved below. (Answers are mentioned at first and explanation is explained in note…

Q: ite a for loop to print all even numbers betw . Repeat with a while loop. . Write a for loop which…

A: 14. For loop to print even numbers b/w 1 to 20For m=1:20If (mode(m,2))=0display(m)endend15. Repeat…

Q: B1 1.- You have the following manufacturing system: 10% I M1 10% 20% I 90% B21 AS * the total…

A: "Since this is a question with multiple sub parts therefore solutions to only first three sub parts…

Q: Select a suitable material for aircraft wing. Aircraft Wing 1) Product identification and Design…

A: As this is a multipart question , as per the guide lines I am answering the first three parts…

Q: Name two distinct advantages of theTenergy methods. For the toolbar, press ALT+F10 (PC) or…

A: Definition of energy method-The Energy Method is a general modeling technique, any multidisciplinary…

Q: 2.10. Compute the long-term average throughput, cycle time and x-factors for this factory for fixed…

A: The given factory uses a serial flow paradigm, in which components pass sequentially through four…

Q: Identify the following items for each of the datum target areas: the datum reference, specified…

A: A datum reference or just datum is some important part of an object—such as a point, line, plane,…

Q: Dr. Deduction has a peculiar penchant for using elaborate experimental se- tups and convoluted…

A: Since each element of the system is connected trough a single cord, the acceleration of each element…

Q: Explain the purpose of the feature control frame below clearly and completely. Datum A is the size…

A: A feature control frame used to describe the conditions and tolerance of a geometric control on a…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.