The velocity distribution in the boundary layer is given by U= point velocity at distance y U = free stream velocity 8 = nominal thickness What would be the displacement thickness(6*)? 1/7 = - (2) ¹/²

Q: Problem # 3: The steel bars are firmly attached to rigid supports. Initially the temperature is…

A:

Q: Velocity profile inside boundary layer is given as, U Ty = sin - sin U. 2 8 Find the value of

A: Following is the given velocity profile:

Q: The state of stress at a point is shown on the element. Suppose 14 ksi, Oy 7 ksi and X 9 ksi in the…

A: Determinea. Principal stresses (σ1, σ2)b. Orientation of the elements (θp1, θp2).

Q: The disk is positioned very close to a solid bou he disk and the boundary is viscous oil. e disk is…

A: According to given data  The disk is positioned very close to a solid boundary. Between the disk and…

Q: A reasonable approximation for the two-dimensional incompressible laminar boundary layer on a flat…

A: Given- u=U2yδ-y2δ2   for y≤δ

Q: Problem 4- For the following cross section (all dimensions in mm) determine: a) The location and…

A: Calculating the location of neutral axis,

Q: A 75-mm-square-bar with length of 3 meters is subjected to a tensile load P = 900 KN. If E = 100 GPa…

A:

Q: A point on a thin plate is subjected to the two successive states of stress shown in Figure 1.…

A: A point is subjected to two stress conditions, we need to determine the resultant stress on the…

Q: : The state of plane stress at a point is represented by the stress element shown in figure 2. Apply…

A: Major principal stressδ1 = -80MpaMinor principal stressδ2 = 50MpaInclined angle θ = 30∘

Q: Question 2 Referring to the stresses on the surfaces of an element in Figure Q.1, determine : (a)…

A:

Q: Determine the average values of strain components at point A shown.

A: Strain: - It is defined as the ratio of change in size to actual size of given object. Strain is…

Q: A 7,607 Ib force (Q) is applied over a circular rigid plate of radius (r) 5 inches sitting on an…

A:

Q: The velocity distribution of a viscous liquid (dynamic viscosity= 0.81 Pa-s) flowing over a fixed…

A:

Q: Thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the…

A: Thin square plate PQRS;a = 200 mm,b = 202.1 mm,c = 198.9 mm.We have to determine-1. Shear strain xy…

Q: At the proportional limit, a 29 mm wide by 12 mm thick bar elongates 1.7 mm under an axial load of…

A:

Q: Problem # 4: Three links are used to support load P 10.25 kips. Disregarding any deformation for…

A:

Q: Determine the stress components at point H. And show the stress state for this point on a volume…

A: Given Data: Axial Load for Point H is P=3 kN. Shear Load for Point H in Y direction is VY=0.5 kN.…

Q: stress tensor at a point is given by the following 6x = 40 oy = 30 oz = 20 MPa, Txy 20 MPa, ryz 40…

A:

Q: This is an exercise to illustrate the effects of mesh refinement on a 1-d rod. To estimate the…

A: Do = 3m R  1.5m α = 0.3 So, d = 0.3x3 = 0.9m r = 0.45m L= 5m

Q: What will be max. height that the water tank that will become full if the max. tangential stress is…

A:

Q: stress distributi e80 MPa.

A: Given data Extension length=40mm from the neutral axis σy=280MPa

Q: No. Load Elongation L. P(KN) SL(mm) W. (mm) Area Ở eng (KN/m²) E eng (mm) m2 1 100 36.1 38 0.02 100…

A: Assuming square section of side W0. S.No. Load P (KN) Elongation (mm) L0 (mm) W0 (mm) Area…

Q: Question The state of 2D-stress at a point is given by the following matrix of stress: [100 30. 30…

A: Given- State of 2D-stress given- σx=100 MPa,σy=20 MPa,σxy=τxy=30 MPa,   It is needed to find the…

Q: Find the displacement thickness, the momentum thickness and energy thickness for the velocity…

A: The velocity distribution is given as,

Q: Sieve Designation Weight retained, g % Retained Weight passing, g % Passing 3" 75 mm 1010 100 2-…

A: size  wt retained cumm wt retained cumm % retained % finer  4.75 450.83 450.83 44.71588 55.28412…

Q: passing through the passes through dist below. The ratio y

A: solution of above problem is below:

Q: Example 1: solve the equation = a?u 6x²(2y – 1)given the ax2 du sin2y and u = cosy. boundary…

A: Equations,d2udx2 = 6x22y - 1Boundary condition,x = 0,dudx = sin2yu = cosy

Q: The bar shown in Figure is subjected to a tensile load of 160 kN. If the stress in the middle…

A: Given data,  Force = 160 kN Stress =  150 N/mm² E = 2.1x10^5 N/mm²

Q: At the proportional limit, a 45 mm wide by 9 mm thick bar elongates 2.5 mm under an axial load of…

A:

Q: Explain the following terms briefly: (i) Displacement thickness. (ii) Von Karman Approximation…

A: (iii) Lift is the component of force perpendicular to and Drag is a force parallel to the flow…

Q: Determine the thickness of the boundary layer at the trailing edge of a smooth plate of length 4m…

A:

Q: The Particle -size distribution of the following: soil A : Sand 25%; Clay 30%; Silt 50% Soil B:…

A: Given: Soil A and Soil B having following distribution Soil A: Sand 25%, Clay 30% and silt 50%…

MATLAB

MATLAB software is a registered trademark, multi-model programming language, and numerical computing environmental system created by MathWorks. 'MATLAB' is the short-form of "Matrix Laboratory". The MATLAB software permits the utilization of matrix operations, graphical representation of data, execution of algorithms, development of user interface, and linking programs created in other languages. Even though MATLAB is developed mainly for numerical computing, there is an optional toolbox that uses a symbolic engine known as MuPAD giving access to all the symbolic computing abilities. In addition to this, a Simulink package delivers graphical multi-domain simulation and design that is model-based for embedded and dynamic systems. MATLAB users are spread worldwide across the world and use MATLAB extensively.