The unyielding supports are firmly attached to the composite bar in this illustr- An axial load P=200 kN is applied at C towards CA at 20 degrees celsius. (1) Find the stress segment 1 and 2 at 60 degrees celsius. (2) At what temperature will segment 1 and 2 have numerically equal stress? A Segment 1 Segment 2 P=200 kN -300mr.- -200mm- Properties of the composite beams Segment 1 C. = 11.7 um/m'c E = 200 GPa A = 1200 mm2 AC = 300 mm Segment 2 a = 23 umim'C E = 70 GPa A = 900 mm? CB = 200 mm %3D

The unyielding supports are firmly attached to the composite bar in this illustr- An axial load P=200 kN is applied at C towards CA at 20 degrees celsius. (1) Find the stress segment 1 and 2 at 60 degrees celsius. (2) At what temperature will segment 1 and 2 have numerically equal stress? A Segment 1 Segment 2 P=200 kN -300mr.- -200mm- Properties of the composite beams Segment 1 C. = 11.7 um/m'c E = 200 GPa A = 1200 mm2 AC = 300 mm Segment 2 a = 23 umim'C E = 70 GPa A = 900 mm? CB = 200 mm %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2420 N-m acting about the z axis. Assume b=64 mm, d1=36 mm, d2=13 mm. Determine: (a) the maximum bending stresses opy,Gal in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) d2 Aluminum (1) Brass (2) dz b Answers: (a) obr = i MPa, oal = i MPа. (b) Obrj MPa.
H.W 3 Two aluminum alloy plates (2) are attached to the sides of a wooden beam (1) as shown in Figure 3. mensions of the composite cross section are b1 = 80 mm, d¡ = 240 mm, b2 = 10 mm, d2 = b2 The di- |di 120 mm, and a = 60 mm. Deter- (2) (2) %3D mine the maximum bending (1) a stresses produced in both the wooden beam and the aluminum b1 plates if a bending moment FIGURE 3 +6,000 N m is applied M2 %3D about the z axis. Assume that Ej = 12.5 GPa and E2 = 70 GPa.
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 70 GPa] bars, as shown. The beam is subjected to a bending moment of 400 N-m acting about the z axis. Using a = 15 mm, b = 100 mm, c = 30 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum y Brass Aluminum b Brass C a d
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 73 GPa] bars, as shown. The beam is subjected to a bending moment of 445 N-m acting about the z axis. Using a = 15 mm, b = 125 mm, c = 30 mm, and d = 75 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Z Aluminum C Aluminum Answers: (a) Ogl Brass (b) Obr= i i b Brass a MPa MPa
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 270 mm, a wall thickness of 15 mm, and a length of 5.5 m. The pipe supports a compressive load of 635 kN. After the temperature of the pipe drops 45°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= i mm mm
Question # 1: The composite beam is made of steel (4) bonded to brass (B) and has the cross section shown. If the allowable bending stress for the steel is (sallow) st = 180 MPa, and for the brass (sallow) br = 60 MPa, determine the maximum moment (M) that can be applied to the beam Ebr 100 GPa, Est= 200 GPa B Question # 2: Determine the maximum shear stress acting at section a-a in the beam. 150 N/m m 8000 N Bla 1.5 m 1.5 m 50 mm 50 mm 200 mm 175 mm 200 mm -B 400 mm 75 mm 600 mm 75mm
QU A composite beam is fabricated by bonding a steel bar and a brass bar and is subjected to the bending moment M = 200 N-m. Determine the maximum bending stress in the brass and steel. Given: E, =200 GPa, E, = 100 GPa Brass 20 }o | Jakrtal
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 185 mm, a wall thickness of 5 mm, and a length of 5.0 m. The pipe supports a compressive load of 675 kN. After the temperature of the pipe drops 39°C, determine:(a) the axial deformation of the pipe.(b) the change in diameter of the pipe.
A composite beam is made of two brass [E = 112 GPa] bars bonded to two aluminum [E = 69 GPa] bars, as shown. The beam is subjected to a bending moment of 350 N-m acting about the z axis. Using a = 15 mm, b = 115 mm, c = 25 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Z Aluminum с Aluminum Answers: (a) Jal= (b) Obr= Brass i y i b Brass a a MPa MPa
H.W 3 Two aluminum alloy plates (2) are attached to the sides of a wooden beam (1) as shown in Figure 3. mensions of the composite cross section are bj = 80 mm, d1 = dz 240 mm, b2 = 10 mm, d2 = The di- di %3D %3D 120 mm, and a = 60 mm. Deter- (2) (2) (1) mine the maximum bending stresses produced in both the wooden beam and the aluminum b1 plates if a bending moment M = +6,000 N m is applied about the z axis. Assume that E = 12.5 GPa and E2 = 70 GPa. FIGURE 3 %3D