I need the answer as soon as possible The unknown resistance Ru of a resistance thermometer is to be measured by abridge circuit of the form shown figure The nominal thermometer resistance attemperature of 20 °C, is 1000 and the sensitivity of the thermometer is 400m2per C.Part A. Calculate the temperature measurement sensitivity in bridge output volts(i.e., Vout) per C that occurs when there is a small change in the resistance of thethermometer.Part BCalculate the error of measurement sensitivity in bridge output volts (i.e., Vout) per Cwhen| there is a small change in the resistance of the thermometer and the internalresistance of the voltmeter is neglected.R,1002Vin =10 VIKOIKO10KΩout

Answered: Image /qna-images/answer/1cd9b7d5-ceeb-406b-9208-cf9aae9cf177.jpg

The unknown resistance Ru of a resistance thermometer is to be measured by a bridge circuit of the form shown figure The nominal thermometer resistance at temperature of 20 °C is 1000 and the sensitivity of the thermometer is 400m2 per °C. Part A Calculate the temperature measurement sensitivity in bridge output volts (i.e., Vout) per oC that occurs when there is a small change in the resistance of the thermometer. Part B Calculate the error of measurement sensitivity in bridge output volts (i.e., Vou) per C when there is a small change in the resistance of the thermometer and the internal resistance of the voltmeter is neglected. R, 1002 V =10V IKO IKO 10KΩ

The unknown resistance Ru of a resistance thermometer is to be measured by a bridge circuit of the form shown figure The nominal thermometer resistance at temperature of 20 °C is 1000 and the sensitivity of the thermometer is 400m2 per °C. Part A Calculate the temperature measurement sensitivity in bridge output volts (i.e., Vout) per oC that occurs when there is a small change in the resistance of the thermometer. Part B Calculate the error of measurement sensitivity in bridge output volts (i.e., Vou) per C when there is a small change in the resistance of the thermometer and the internal resistance of the voltmeter is neglected. R, 1002 V =10V IKO IKO 10KΩ

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i need the answer quickly
a metal device box has four 12 AWG conductors, two internal clamps, and a duplex receptacle. Total voume ? Device boxsize ?
COLUMN A COLUMN B A copper wiring containing 8 color-coded 1. conductors or 4 twisted pairs that offers greater bandwidth for local area networks. A. LEGEND 2. distribution device. A wiring pattern that connects to a central B. HOMERUN 3. Another term for an 8-pin modular jack. C. OVERCURRENT 4. A coaxial cable quad shielded with all copper center conductor used for cable TV. D. INSULATOR It is the maximum current that a conductor can 5. carry without exceeding its temperature rating. E. SHORT CIRCUIT 6. A wiring job where many cables enter a device or a junction box that is considered an unsafe practice in electrical wiring, F. CIRCUIT BREAKER 7. An electrical safety device designed to protect an electrical circuit from damage. G. ARC FLASH 8. unintended path with very low resistance. Occurs when an electrical current flows in an H. AMPACITY 9. amperage capacity of the circuit. Occurs when the current exceeds the rated I. UTP 10. A method of extending an electrical wire to the ground…
15. _______ is a proximity sensor that uses the principle of ‘eddy current’ to sense the presence of an object.
3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
Untitled form Your email address will be recorded when you submit this form. Not eng.refcon.k2324@sadiq.edu.iq? Switch account objective question(jW Jlgs) For the circuit shown below choose the correct answer V2 Vi SA 220 300 25A In 31
What is the lighting and receptacle demand load for an 1000 sq. m office space with one hundred ten, 15 A, 250 V receptacles. [Office General Lighting Receptacle]
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.
Please answer in typing format