The uniform slender rod shown in (Figure 1) has a mass of 8.0 kg.Figure200 mm600 mm-< 1 of 1 >▾ Part AIf the cord at A is cut, determine the reaction at the pin O, when the rod is still in the horizontal position.Express your answer to three significant figures and include the appropriate units.Fon=SubmitPart BFor=SubmitμAValueProvide Feedback1Request AnswerDetermine the reaction at the pin O, when the rod swings to the vertical position.Express your answer to three significant figures and include the appropriate units.Ti μA 1ValueUnitsRequest Answer2?Units?

Answered: Image /qna-images/answer/9e1a86e2-28ed-438f-b15d-3ab4d724e7e8.jpg

The uniform slender rod shown in (Figure 1) has a mass of 8.0 kg. Figure 200 mm 600 mm- < 1 of 1 > ▾ Part A If the cord at A is cut, determine the reaction at the pin O, when the rod is still in the horizontal position. Express your answer to three significant figures and include the appropriate units. Fon= Value Submit Part B FOU= μA Submit Provide Feedback 1 Request Answer Determine the reaction at the pin O, when the rod swings to the vertical position. Express your answer to three significant figures and include the appropriate units. μA 1 Value Units Request Answer 2 ? Units ?

The uniform slender rod shown in (Figure 1) has a mass of 8.0 kg. Figure 200 mm 600 mm- < 1 of 1 > ▾ Part A If the cord at A is cut, determine the reaction at the pin O, when the rod is still in the horizontal position. Express your answer to three significant figures and include the appropriate units. Fon= Value Submit Part B FOU= μA Submit Provide Feedback 1 Request Answer Determine the reaction at the pin O, when the rod swings to the vertical position. Express your answer to three significant figures and include the appropriate units. μA 1 Value Units Request Answer 2 ? Units ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure on the left, below, shows a non-uniform bent rod with a mass of 5 kg. Your job is to determine the location of the center of gravity of this rod. You design an experiment: you connect a pin and cable to the rod such that it safely stays in static equilibrium under a force P that you apply. Then, you apply forces between 0-100 N, and measure the tension force on the cable using a cable tension meter. The results of your experiment are shown in the figure, on the right. Using this experiment, calculate (approximately) the horizontal distance (x in the figure) between point A and the center of gravity G of the bent rod. B C O I 20 cm 20 cm 60° D 50 cm Tension measurement [N] 60 50 40 30 20 -10 0 10 real data estimated fit 20 30 40 ܐܐܝ 50 P[N] 60 70 80 90 100
Determine the tension developed in the cable AC required to support the traffic light Express your answer to three significant figures and include the appropriate units. HA ? FAC = Value Units Submit Request Answer Part C Figure 1 of 1 Determine the tension developed in the cable AD required to support the traffic light Express your answer to three significant figures and include the appropriate units. 6 m ? HA 3 m FAD = Value Units 4 m 4 m Submit Request Answer 3 m 4 m 6 m 4 m 3 m y Provide Feedback
1) Determine the reaction at roller A. Express your answer to three significant figures and include the appropriate units. 2) Determine the horizontal and vertical components of reaction at pin B(Bx,By) . Express your answers in newtons to three significant figures separated by a comma.
The lifting arm shown below needs to lift a weight of 4 (N). Assuming the links are weightless, determine the magnitude of the force being applied by the pin at B on the lifting arm to the nearest hundredth of a newton. 10Em) 6icm- 150 A Servo Horn Arm 4 (W) 'Servo
1) Determine the horizontal component of reaction at pin Cx . Express your answer to three significant figures and include the appropriate units. 2) Determine the vertical component of reaction at pin Cy Express your answer to three significant figures and include the appropriate units.
- Required information A helical compression spring is made of hard-drawn spring steel wire of diameter 0.0773in. and has an outside diameter of 0.85 in. The ends are plain and ground, and there are 8 coils. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the pitch of this spring? What force is needed to compress the spring to its solid length? Estimate the spring rate. The pitch of the spring is in. The force needed to compress the spring to its solid length is lbf. The spring rate is lbf/in.
When the two forces are placed on the beam, the diameter of the A-36 steel rod BC decreases from 40 mm to 39.96 mm. (Figure 1) Figure -1 m -1 m P -1 m- B 0.75 m 1 m Part A Determine the magnitude of each force P. Express your answer to three significant figures and include the appropriate units. P = μA Value KN Submit Previous Answers Request Answer Provide Feedback ? X Incorrect; Try Again; 2 attempts remaining
In-1' 16+29 CHAPTER ENGINEERS MECHANICS STATICS り」 arc ( 24 X(x Sample Problem 6.4.2 JQ) aX9 142 i JA V4 TuS 31 An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The minimum force P required to prevent rotation of the flywheel is applied. 800 N.m dre 2.R 1. Which Tension is larger, TA or TB? Explain 2. What is the angle of contact in radians? 60 3. What is the value of the ratio TA/TB? A B X*ッー Sin=d 6+ミ 2(I+(T Tarc (2) 4)e Eら、1.2 J =3.
The 80-lb door has its center of gravity at G. (Figure 1) Figure 1 of 1 18 in. 24 in. 24 in. 18 in.
In our data run, we zeroed the force sensor at the cart's equilibrium position. Name the total force to stretch the spring F = ky. Name the force to stretch the spring to the cart's equilibrium position F, = ky,. Name the difference in the force to move the cart from the equilibrium position, F. So that F = F, +F, 23. Write the expression for F, in terms of y,, y, and k ?
Pivot A constant density bar with mass m and length Lis held in place as shown. Use the usual x,y,z coordinates for the following questions. Celling Cable 12. Measuring from the pivot, in the space below draw the torque-pic for the weight force exerted on the bar. Be sure your torque-pic includes both an expression for r in terms of L and also the value for the angle between r and weight force. Bar 350 Length = L
The couple moment acting on the pipe has a magnitude of 180 Nm (Figure 1). Figure -F A -150 mm. 150 mm B F 200 mm 600 mm 1 of 1 Part A Determine the magnitude F of the forces applied to the wrenches. Express your answer to three significant figures and include the appropriate units. F = Submit 0 μĂ Value Request Answer < Return to Assignment Units Provide Feedback ?