The uniform pole in (Figure 1) has a weight of 30 lb and a length of 26 ft. The coefficient of static friction between the floor and the pole is μ = 0.22. Figure 26 ft 1 of 1 Part A Determine the maximum distance d it can be placed from the smooth wall and not slip. Express your answer to three significant figures and include the appropriate units. d= μA Value Submit Request Answer Units ?

Q: Determine Iy. 50 mm 50 mm 300 mm 50 mm y -200 mm an -X We Problem 4

A:

Q: %o change in diamefesx-?

A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a…

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A: If A= 0.375 inch, B=0.923 inch, C=1.0992 inches,find G.

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: 2. Determine the reading on the vernier scale as indicated by the arrows. 25 30 35 40 10 20 30 40 50…

A: Least count of Vernier caliper = 0.02 mm

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: What is the Neutral Axis?

A: The neutral axis is the fiber of the beam with no normal stress. When a beam is subjected to a…

Q: how did the equation simplify to a = 0.984?

A:

Q: 150 m 50 mm 85 mm Section X-X 20 kN

A:

Q: Using the diagram, determine the minimum diameter for DIA B, in inches. DIA A +0000 o 0.001 6 BASIC…

A:

Q: name these lines

A: The names of the given lines is given below.

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: Problem 2: Values: FA = 20 N FB = 30 N a = 25° Use the graphical method to determine... a) the…

A:

Q: What is the v-velocity at the centerline after refining the mesh

A: To explain: What is the v-velocity at the centerline after refining the mesh.

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.