The ultimate load capacity of a 10 m long concrete pile of square cross section 500 mm x 500 mm driven into a homogeneous clay layer having undrained cohesion value of 40kPa is 700 kN. If the cross-section of the pile is reduced to 250 mm x 250 mm and the length of the pile is increased to 20 m, the ultimate load capacity will be 350 kN 632.5 kN 1400 kN 722.5 kN

Q: 90 Engineering Drawing الفصل الثالث شكل رقم 13 R20 40 35 55 9. 30

A: Providing Here the View for Front View, Top View and Left Side Views.

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral.…

A:

Q: 16m 8m 60° 126m 120m 20m 64m 16m

A:

Q: Locate the centroid 10 mm 20 mm 10 mm 10 mm 20 mm 50 mm y

A:

Q: y at point B

A:

Q: y 500 50 80 -140- - 140- 80 60 400 500 50 500

A: Given- plate area is given  To find- centroid of given plate area

Q: Determine the coordinates of the centroid of the shaded area. y | 25 E 50 60 25 60 70 50. --x 170…

A:

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: 31⁄5 / 4⁄7

A: 31/5=6.2 4/7=0.571

Q: BEGO AV 6 MM CM X 2 2 5 24 INCH Styles Title 1 No Spac..... Question 2: Given that this soccer field…

A: Given Goal to goal distance = 100 m Required  Representative factor,RF of image

Q: Q1: determaine the coordinates of the centeroid of the shaded area 20 40 50 20 40 30 140

A: The polar coordinate system is a method to calculate points in the system location by proper…

Q: 5 ft 8 ft 2 ft A -3 ft- XB 3 5 4 30 lb B P

A:

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: PROBLEM 2: Determine Ix and Tx.

A: given- a plane figure to find- M.O.I  about X-axis and centroidal axis.

Q: The representation of the hinge lines of the glass box in a drawing are known as lines. ....** .....…

A: The glass box concept is used in orthographic projection. When the glass box is visualized, then…

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: 5 10 35 30 11E 25 10 15 20 25 .001 in. 10

A: 3 English Fixed scale reading = 0.8inch 4 English Vernier scale = 16 Least count = 0.001 inch Net…

Q: 3. A simply supported beam of 6 m, see cross-section below is subjected to a concentrated load of…

A: Using bending equation

Q: Assignment 7.: Draw the Projection (Front View & Top View) of a point "G" which is present on the HP…

A: We will draw the projection of the point G with respect to XY line It will include front view as…

Q: Fullform of CASBEE

A: CASBEE has been designed to both enhance the quality of people's lives and to reduce the life-cycle…

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Q: Y

A:

Q: 12 13 12 13 14 10 Which tools that can be used to :4 draw the following shape in .AutoCAD R5 R10 R12…

A: To draw the given shape we will require the following command necessarily :- Dimension, line or…

Q: 350 mm 250 mm 600 mm Member Magnitude,N X-component Y-Component 180 mm 360 mm G H TBD 240 mm 400 mm…

A: Given- A frame structure is given    To find- forces at joints G H E and Tbd

Q: Define phreatic surface.

A: The term phreatic is used in hydrology and the earth sciences to refer to matters relating to ground…

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.