The two-terminal device shown in Fig. 2 has an internal resistance of 2500 Q. A meter with impedance of 10,000 Q is connected to the outpu perform a vollage measurement. (a) What is the percent error in determination of the internal voltage? (b) Estimate the power transmitted for (1) given load and (ii) when the given meter is replaced by another meter which has impedance equal to the internal impedance of the two term device. Load Fig. 2. Two-terminal device with intemal impedance

The two-terminal device shown in Fig. 2 has an internal resistance of 2500 Q. A meter with impedance of 10,000 Q is connected to the outpu perform a vollage measurement. (a) What is the percent error in determination of the internal voltage? (b) Estimate the power transmitted for (1) given load and (ii) when the given meter is replaced by another meter which has impedance equal to the internal impedance of the two term device. Load Fig. 2. Two-terminal device with intemal impedance

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A voltmeter having sensitivity of 200 ohm/volt reads 119 V on its scale of 219 V when connected across an unknown resistance in series with a multimeter. When the multimeter rads 5mA, calculate the error due to the loading effect of voltmeter. Also calculate the error if the milliammeter reads 800mA and voltmeter reads 40V on its 219 V scale.
SECTION B-Choose any TWO (2) Questions from this Section Question 1 [25 Marks] (a) A commercial building has a power demand of 50 kW at a power factor of 85%. Determine (i) (ii) The annual penalty if the utility's minimum power factor is 95% and the cost of power is P10/kW/month (9) P The cost of capacitor, which when connected in parallel to the load will improve the power factor to 100%. (Assume the purchasing cost of capacitor is P30/kVAR) (10) (b) A 3-phase, 10 kVA load has a power factor of 0.342. The power is measured by two wattmeter method. Find the reading of each wattmeter. Q w Var Va = 10€ Va >= 10kVA pl: 0.36 2 (= Isine 5 3149 Question 2 [25 Marks] (a) A single-phase motor takes apparent power of 1909 VA at a power factor of 0.866 lagging when con- nected to a 230 V, 50 Hz supply. (i) Calculate current drawn from the supply (ii) (b) Draw a fully labelled equivalent circuit of a transformer Two similar capacitors are then connected in parallel with each other to form a…
Range of a generating voltmeter is 30 to 300 kV dc and its indicating meterreads a minimum current of 3μA and maximum current of 35 μA, find the capacitance of thegenerating voltmeter.
Note: Please do not handwritten.
15. An AC ammeter set at 10 A is connected in series with the lamp which is busted/open. What is the current reading? Assume the lamp has a resistance of 10 ohms.
1. A small chrome plating tank needs a 1000 ampere source. Design an ammeter shunt for a 50 µA D'Arsonal meter movement that has a coil resistance of 2500 ohms. What is the resistance of the shunt in parallel with the meter? O a. 50 micro ohms O b. 10 micro ohms O c. 100 micro ohms O d. 125 micro ohms O e. 250 micro ohms
A battery consists of four cells connected in parallel, each having an emf of 24 volts and resistances of 0.40, 0.45, 0.42, 0.46 Ohm. A resistance of 1.50-Ohm is connected across the terminals of the battery. Determine: current; terminal voltage; current in each cell; Efficiency of the system.
Example (2): Design d.c voltmeter by using direct method with d'Arsonval meter of 1002 and full scale deflection of 100µA to give the following ranges: 10mV, 1V, and 100V.
Q: A wood panel containing 16 solar cells. Calculate the total open circuit voltage and short circuit current coming out of the board and draw the relationship between current and voltages in the following cases a) If you connect each two cells in series and connect the groups in parallel . b) If all four cells are connected in parallel and the groups are linked in succession, noting that each cell has the following characteristics: Vos = 0.75V, Isc = 2 mA
Needs Complete solution with complete explanation and 100 % accuracy.