The two reservoirs connected by a smooth pipe below contain water at 20 °C. Ignoring minor losses inthe system what is the flow rate for Az = 97 mif the pipe has the following properties:• L = 7 km• D = 50 mmΔz1DIL, d, E27(a) What is the friction factor? Please provide your answer to 2 significant figures.Number(b) What is the flow rate? Please provide your answer to 3 significant figures.NumberUnits

Answered: Image /qna-images/answer/8ed81667-840f-4301-a5bb-51a6418b1179.jpg

The two reservoirs connected by a smooth pipe below contain water at 20 °C. Ignoring minor losses in me system what is the flow rate for Az = 97 m the pipe has the following properties: • L = 7 km • D = 50 mm L, d, E Δz ▼ a) What is the friction factor? Please provide your answer to 2 significant figures. Number b) What is the flow rate? Please provide your answer to 3 significant figures. Number Units

The two reservoirs connected by a smooth pipe below contain water at 20 °C. Ignoring minor losses in me system what is the flow rate for Az = 97 m the pipe has the following properties: • L = 7 km • D = 50 mm L, d, E Δz ▼ a) What is the friction factor? Please provide your answer to 2 significant figures. Number b) What is the flow rate? Please provide your answer to 3 significant figures. Number Units

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem 3 The figure presents the portion of the pipe network through which a fluid with a specific…

Q: Piezometric tubes are tapped into a pipe section as shown in the figure below. The liquid is…

Q: (a) Develop a model that describes the system (b) Represent the model in the state space form (1)…

A: a.) Model defined the system Water first flows in the tank1 and after filling till a certain height,…

Q: Calculate the shear stress for the illustrated flow to 2 significant figures(dyn/cm2 ; do not use…

A: Given Data: Velocity Vo=7 cm/s. Velocity V=0. Distance d=30 mm. Viscosity of liquid is μ=2…

Q: Stoke's Viscosity - GLYCERIN Temperature = 17 C Fluid: Sp. Gravity of fluid G = Compute density of…

A: Hi there!! since you have asked multiple questions, we will solve the first question for you. If you…

Q: 6. A water is supplied through the pipe network system as shown below. The reservoir water level…

Q: A circular, downward water jet impacts a horizontal plate as shown in the figure below. The exit…

A: A vertical downward jet flow from the pipe impacts a plate kept at a certain distance. The velocity,…

Q: Given the following information about a length of pipe: P1 = 440 kPa V1 = 0.0085 m/s z1 = 5 m v2 =…

A: Applying Bernoulli`s equation between point 1 and 2 in the given pipe flow:…

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

Q: 8. Given the following configuration: 1) What is the specific discharge (= Darcy velocity) in whole…

A: Ke = ∑zi∑ziki

Q: The pressure heads are measured at two sections in a pipeline and are found to be 8.3 m at point A…

A: Step 1: Step 2: Step 3: Step 4:

Q: 1. The Dam ABC has a width of 30 m into the paper and the dam bottom length is 60m. The dam material…

A: We will calculate each moment and find FOS.

Concept explainers

Field applications of hydraulic conductivity

Hydraulic conductivity is one of the hydraulic properties of soil defined as a measurement of the ability of a porous medium to permit water movement or fluid flow through it. It is denoted by the letter K. It is influenced by the density and viscosity of the fluid. It is also called permeability. Hydraulic conductivity is defined as the ratio of velocity to the hydraulic gradient. The different methods used to determine the hydraulic conductivity are laboratory methods (constant head permeability tests and falling head tests), in-situ field methods (pumping in and pumping out tests), small scale field tests (infiltration tests and slug tests), and indirect methods such as estimation from grain size, consolidation test data, and horizontal capillary test. The pedotransfer function (PTF) method is a specific empirical estimating approach employed in the soil sciences is also used to determine the hydraulic conductivity of the soil.

Question

The two reservoirs connected by a smooth pipe below contain water at 20 °C. Ignoring minor losses in
the system what is the flow rate for Az = 97 m
if the pipe has the following properties:
• L = 7 km
• D = 50 mm
Δz
1
DI
L, d, E
27
(a) What is the friction factor? Please provide your answer to 2 significant figures.
Number
(b) What is the flow rate? Please provide your answer to 3 significant figures.
Number
Units

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Field Applications of Hydraulic Conductivity

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 10.56 The 100-mm-diameter commercial steel pipe discharges water at 25°C through the 40-mm-diameter nozzle. (Figure 1) Figure 40 mm g 60e 3m A 100 mm 1 of 1 Part A If the pressure at A is 250 kPa, determine the discharge. The minor loss coefficient of the nozzle is KL = 0.15. Express your answer to three significant figures and include the appropriate units. Q= Submit OL μА Value Provide Feedback Request Answer Units ? (v 5 of 6 Review Next >
Solution step by step..
Problem 8: EGL and HGL (IV) Consider a storage reservoir with a water surface elevation of 270 m. It is connected to a closed conduit (i.e., a pipe) that carries water down to a turbine at elevation 60 m. The friction head loss in the conduit is 20 m. Part A At point D, what are the pressure head P/y, the elevation head z, and the HGL? Part B Copy the diagram below. If the conduit is a closed pipe flowing full, is the velocity head V²/(2g) constant D→E? Answer yes or no, then sketch the EGL above the pipe D-E. Use a solid line. D E z = 270 m T Part C Based on your answer to Part B, sketch the HGL from D-E. Use a dashed line. z = 270 m Part D Now assume the conduit is an open channel. Copy the diagram below. Is the velocity head V²/(2g) constant D→E? Answer yes or no, then sketch the EGL above the pipe D→E. Use a solid line. E D z = 60 m T z = 60 m Part E Based on your answer to Part D, sketch the HGL from D-E. Use a dashed line.
PLEASE USE EQUATIONS ATTACHED 9.95. The mean velocity of water in a 150 mm horizontal pipe is 0.9 m/s. Calculate the loss of head through an abrupt con- traction to 50 mm diameter. If the pressure in the 150 mm pipe is 345 kPa, what is the pressure in the 50 mm pipe, neglecting pipe friction? K₁ from Table 2 for abrrupt contraction find Using work- energy equation Az A₂/A₁ C K₂ 21102392 A1 2.A? 81000.0 1J0321 to 19 1200 to find the pressure. 14 or. Mive stolwlog si/s919 mE.0 P but mop, +V² F 2 P₂ + Cup 2.10 erived one wolf 829) NINY 2.0 = 9 . TABLE 2 Contraction, C., and Loss, Kr, Coefficients for Abrupt Contractions 0 0.617 0.50 0.1 0.624 0.46 0.2 0.632 0.41 0.3 0.643 0.36 0.4 0.659 0.30 V₂² + Z₂ +h₁0/₂ 2 milyot has 9919 0.5 0.681 0.24 0.6 0.712 0.18 0.7 0.755 0.12 0.8 0.813 0.06 0.9 0.892 0.02 1.0 1.00 0
8. Calculate the pore water pressure at point A through I shown on the following flow net. 14 m 10 m CDEFGH
What is pipe roughness? A pump is located 5 m above the surface = 8170 M/m¹) in a closed tank. The pressure in the space above liquid surface is 35 Kpa. The suction line to the pump is 15 m of 15 cm diameter pipe (/= 0.025). The discharge from the pump is 60 m of 20 cm diameter pipe (/= 0.03). The pipe discharges in a submerged fashion to an open tank whose free liquid surface is 3 m lower than the liquid surface in the pressure tank. If pump puts 1.5 kW Into the liquid, determine the flow rate and the pressure in the pipe on the suction side of the pump. Assume turbulent flow.
Two sharp-ended pipes of diameter d₁ = 50 mm, and d₂ = 100 mm, each of length 100 m, are connected in parallel between two reservoirs which have a difference of level h= 10 m, as shown in figure below. If the friction coefficient, f= 0.032 for each pipe, calculate: a. the rate of flow for each pipe, b. the diameter d of a single pipe 100 m long which would give the same flow if it was substituted for the original two pipes, (Notes: Use Darcy Weisbach's equation, h,= (flv²)/(2dg) Pipe 2- Pipe 1 h = 10 m 110
i)Calculate the flow rate through the system.
Water flows through the branching pipe shown in the figure below. The flowrate at section (1) is Q₁ = 1.1 m³/s, and the velocity at section (2) is V₂ = 17 m/s. A₁ = 0.1 m² P1 = 300 kPa 21 = 0 P3 = -147.2 A3 = 0.035 m² Z3 = 10 m (1) (2) If viscous effects are negligible, determine the pressure at section (2) and the pressure at section (3). P2 = i 315.3 kPa kPa (3) A₂ = 0.03 m² 22 = 0
For the selection of friction factor, f from the Moody diagram, select the most appropriate answer. O For smooth-walled pipes, we need to know Re only. O All the answers are correct. O For laminar flow, we need to know Re only. O For rough turbulent flow, we need to know Re vs ks/D.
Consider the pressurized horizontal pipe network shown below. Pipe 2 is arranged in parallel with Pipe 3. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 10 cfs and the pressure head at Node A is yA = 180 feet. The temperature of the water is 60° F. a) Determine the flow in cfs in Pipe 2. b) Determine the flow in cfs in Pipe 3. c) Determine the friction head loss hric in feet in Pipe 1. d) Determine the friction head loss hfic in feet in Pipe 2. e) Determine the friction head loss htric in feet in Pipe 3. f) Determine the friction head loss hfric in feet in Pipe 4. g) Determine the pressure head ys in feet at Node B. h) Determine the pressure head yc in feet at Node C. i) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Pipe (inches) (feet) Friction (cfs) head Нead factor f Kpipe loss (feet) Node (feet) 1 16 500 0.012 10 A 180 12 1000 0.014 B 10 1000 0.015 16 500 0.020 10 D Pipe 2 Node Node Node…
Consider the pressurized horizontal pipe network consisting of three pipes arranged in series. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 5 cfs and the pressure head at Node A is yA = 200 feet. The temperature of the water is 60° F. a) Determine the friction head loss hfric in feet in Pipe 1. b) Determine the friction head loss hfric in feet in Pipe 2. c) Determine the friction head loss hfric in feet in Pipe 3. d) Determine the pressure head ys in feet at Node B. e) Determine the pressure head yc in feet at Node C. f) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Friction (feet) (cfs) head Нead Pipe (inches) factor f Kpipe loss (feet) Node (feet) 1 16 500 0.011 5 A 200 2 12 1000 0.013 B 3 10 750 0.015 D Node Node Node Node A в D 5 cfs 5 cfs Pipe 1 Pipe 2 Pipe 3