The two loads shown in the figure below can be described as follows: Load 1 absorbs an average power of 60 kW and delivers 70 KVAR magnetizing reactive power, Load 2 has an impedance of 24 +j 7 2 The voltage at the terminals of the loads is 2500 v2 cos 120nt V. a) Find the ms value of the source voltage. b) By how many microseconds is the load voltage out of phase with the source voltage? c) Does the load voltage lead or lag the source voltage? 0.05 N j0.5 N VL L2 0.05 Ω j0.5 Ω

The two loads shown in the figure below can be described as follows: Load 1 absorbs an average power of 60 kW and delivers 70 KVAR magnetizing reactive power, Load 2 has an impedance of 24 +j 7 2 The voltage at the terminals of the loads is 2500 v2 cos 120nt V. a) Find the ms value of the source voltage. b) By how many microseconds is the load voltage out of phase with the source voltage? c) Does the load voltage lead or lag the source voltage? 0.05 N j0.5 N VL L2 0.05 Ω j0.5 Ω

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Three loads are connected in parallel to a 240-V, 60 Hz supply. Load 1 is composed of three 600-W heaters, Load 2 is a 3 HP, inductive motor with an efficiency of 90% and a p.f. of 0.88, while Load 3 has an impedance of 12-j16 ohms. Determine the following: a) The apparent power of each load b) The Total Power, Total Reactive Power, Total Apparent Power, Power Factor c) The source current
What is the value of capacitance that needs to be connected in a parallel configuration to the load in order to correct the pf source to 0.94 lagging. Frequency f= 129 Hz
A load of 240 +j 120 is connected to a source of 480 V with a phase angle of 300, through a transmission line with an inductive reactance of 60 ohms. A Capacitor bank of a capacitive reactance of 120 ohms is connected in parallel to the load. Total reactive power supplied by the source is: O A. 5760 vars O B. None of choices are correct O C. 1920 vars O D. 1920 vars O E. 3840 vars
1. Solve for I rms. 0.785 and b = 3.37. a = i(wt) = 21.8 sin (wt – 1.312) – 50 + 75.0e¯®t/3.77 A for 0.785
IL 220230° Load P = 2 kW pf = 0.9 lag Assuming that the source is operating at 60 Hz, determine the following: a.) The value of the current I, in phasor form the magnitude, degrees for the angle) b.) What is the reactive power Q of the load in (volts for KVAR? c.) Is the load consuming or supplying Q? d.) What is the apparent power S of the load in KVA? e.) What is the load resistance? Express your answer in Ohms. f.) What is the load inductance? Express your answer in millihenries.
Two loads are connected in parallel to a 2000 V(rms) 50Hz source. one of the loads Each of them has 500KVAR reactive power and 0.6 reverse power factor. Other load 300KW since it has absorbing power and 100KVAR dissipating power a) Draw the equivalent circuit of the system b) Find the common power factor of the system c) In order for the power factor to be 0.98 back, the capacitor to be connected in parallel with the loads find its value d) The magnitude of the current drawn from the source is measured before and after the capacitor is connected Find and compare for the next cases. Not. Solve this question in detail step by step and explain your requests in detail
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following: e. Reactive power supplied by the sourcef. Apparent power of the circuitg. Power factor of the entire circuit
A 25 kVA, 240 V single phase source supply the rated power at the rated voltage to a motor at 0.8 power factor lagging. Find the capacitor bank in order to improve the power factor to 0.9 lagging. connected to a motor. a. Calculate the real power, reactive power and current before capacitor bank is connected? P= Q= b. Calculate the power and reactive power after capacitor bank is connected? P = c. What is kVA rating of capacitor bank Qc?
Problem 1 • A sinusoidal source with frequency of 60 Hz and rms-voltage of 100 V is connected to an RL load of 10 ohms and 100 uH. Find Power Factor From Calculation Find Power Factor From Plot L=10mH find power factor from calculation only
find The average power delivered to * .the circuit الحل بطريقة الممانعات وشكرا
Solve 9
For a source which has load has the following characteristics: • Vrms = 125 20° V • P= 400 W • pf = 0.925 lagging What is the rms current and reactive power?