Solving dynamics problems in steps:1. Collect data and assumptions2. Desired result?3. Make drawing/sketch of the (sub)problem4. Equations and calculations5. Answer and conclusionsFurthermore:---Write down the steps clearlyCheck intermediate results (accuracy)Dimension check and units!Magnitude of number in line with expectation? Question 4:The two identical links, each of length b andmass m, may be treated as uniform slender bars.If they are released from rest in the positionshown with end A constrained by the smoothvertical guide, determine the velocity v withwhich A reaches O with essentially zero.Ab6B

Here we will apply the principle of energy conservation.

The two identical links, each of length b and mass m, may be treated as uniform slender bars. If they are released from rest in the position shown with end A constrained by the smooth vertical guide, determine the velocity v with which A reaches O with essentially zero.

The two identical links, each of length b and mass m, may be treated as uniform slender bars. If they are released from rest in the position shown with end A constrained by the smooth vertical guide, determine the velocity v with which A reaches O with essentially zero.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 150 kg spool below is initially at rest and has a radius of gyration of kg 0.5 m. The force Pis applied at B and causes the spool to begin rotating. The rope attached to point A does not slip at its contact point with the spool, meaning that point is an instantaneous center of zero velocity as shown. However, the bottom of the spool slips against the ground, causing a frictional force which acts to the right. After 5 s the angular velocity of the spool is -27 rad/s (using the coordinate system shown, meaning the spool rotates in the clockwise direction). Based on this information: a) Find the moment of inertia of the spool at the instantaneous center of zero velocity. b) Calculate the frictional force exerted on the spool by the ground. c) Using the principal of angular impulse and momentum, determine the coefficient of kinetic friction, r, between the bottom of the spool and the ground. IC 0.75 m 0.25 m P = 800 N 0.5 m B
: The 3-lb collar is released from rest at A and slides freely up the inclined rod, striking the stop at B with a velocity v. The spring of stiffness k 1.8 lb/ft has an unstretched length of 15 in. Calculate the kinetic energy = and v. Note: Use the equation of principle of work and kinetic energy in solution. BAB k= 1.60 lb/ft 18" wwwwww 20" 10"
(a) Two blocks are joined by an inextensible cable as shown in Figure. If the system is released from rest, determine the velocity of block A after it has moved 2 m by using the data given. Assume that the coefficient of kinetic friction between block A and the plane is ?k = 0.25 and that the pulley is weightless and frictionless.
The initially stationary uniform disk of mass m₁ = 2.2 kg and radius b = 265 mm is allowed to drop onto the moving belt from a very small elevation. Determine the time t required for the disk to acquire its steady-state angular speed. The belt drive pulley rotates with a constant counterclockwise angular velocity w = 125 rad/s. The mass m₂ is 4.9 kg, the coefficient of friction is 0.17, and the radius r of the small pulley is 37 mm. Ignore any sag in the belt. 36 my b A 0 Ha Answer: t = i m₂ 00 S
The slider of mass m is released from rest in position A and slides without friction along the vertical‐plane guide shown. Determine the height h such that the normal force exerted by the guide on the slider is zero as the slider passes point C. For this value of h, determine the normal force as the slider passes point B.
A 173-lb snowboarder has speed v = 15 ft/sec when in the position shown on the halfpipe. Determine the normal force on his snowboard and the magnitude of his total acceleration at the instant depicted. Use a value HK = 0.06 for the coefficient of kinetic friction between the snowboard and the surface. Neglect the weight of the snowboard and assume that the mass center G of the snowboarder is 2.2 feet from the surface of the snow. 27° G 21' Answers N = a = i i 21' lb ft/sec²
The 160-lb exerciser is beginning to execute a bicep curl. When in the position shown with his right elbow fixed, he causes the 20-lb cylinder to accelerate upward at the rate 0.30g. Neglect the effects of the mass of his lower arm and estimate the normal reaction forces at A and B. Friction is sufficient to prevent slipping. B A <12" 12" 16" 19° 57" 20 lb
IV. For the following system that starts from rest, the spool has a weight of 300 N and a radius of gyration ke = 0.3 m, and block A is attached to it as shown of weight 200 N. A constant horizontal force F is applied to the cord in order to give the block an upward speed of 5 m/s. (Neglect mass of cord and tension force). -F 1. Draw the free body diagram of the system. 2. Calculate the angular speed of the spool at t= 6 seconds. 3. Calculate the vertical reaction force at the pin at t= 6 seconds. 4. Calculate the horizontal force F.
Solve correctly please.
Calculate the work friction Q
The spring of constant k is unstretched when the slider of mass m passes position B. If the slider is released from rest in position A, determine its speed as it passes points B and C. What is the normal force exerted by guide on the slider at position C? d tion B Slider TAT 18* & quide
A uniform crate C with mass m is being transported to the left by a forklift with a constant speed v1 . What is the magnitude of the angular momentum of the crate about point D , that is, the upper left corner of the crate?a. 0b. mv 1ac. mv 1 bd. mv 1