The two homogeneous bars AB and BC areconnected with a pin at B and placed betweenrough vertical walls. If the coefficient of staticfriction between each bar and the wall is 0.4,determine the largest and for which the assemblywill remain at rest.Tut Probleme Week 117-4 The two homogeneous bars AB and BC are connected with a pin atB anplaced between rough vertical walls. If the coefficient of static friction betweeneach bar and the wall is 0.4, determine the largest angle e for which the assemblywill remain at rest.600 mm600 mm8 N6 N

The angle θ is the same for both the rods. So, analyse one rod for θ. Consider the free-body diagram…

The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.4, determine the largest and for which the assembly will remain at rest.

The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.4, determine the largest and for which the assembly will remain at rest.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The plate of thickness, t 5 mm, is loaded with the following stress; o, = 100 MPa, o, = -60 MPa, E = 200 GPa, v 0.33. If a = 160 mm, and b= 200 mm, y C Calculate the change in the length (mm) of AB.
Problem 7. [Concepts: Allowable stresses and factor of safety] Two aluminum rods AB and AC support a vertical load P. The allowable tensile stress for the aluminum is Gallow = 150 MPa. a) If P = 20 kN, determine the required diameters of the rods AB and AC. b) If the diameters of the rods AB and AC are 10 mm and 8 mm, respectively, determine the largest vertical force P that can be supported. U B
I need the answer as soon as possible
135 mm 85 mm σ, = -58 MPa E = 105 GPa D = 0.33 Beer & Johnston & DeWolf & Mazurek 2.86 (a) For the axial loading shown, determine the change in height and the change in volume of the brass cylinder shown. (b) Solve part a, assuming that the loading is hydrostatic with Ox= Oy = O₂ = -70 MPa
10. The rigid bar below is supported by axial bar (1) and by a pin connection at C. Axial bar (1) has a cross-sectional area of A₁ = 275 mm², an elastic modulus of E = 200 GPa, and a coefficient of thermal expansion of a = 11.9x 106/°C. The pin at C has a diameter of 30 mm. After load P has been applied and the temperature of the entire assembly has been increased by 31°C, the total strain in bar (1) is measured as 975 μe (elongation). Determine: (a) the magnitude of load P. (b) the shear stress in pin C. 275 mm Connection detail (1) Rigid bar 540 mm 135 mm 260 mm
Determine the stresses for each segment when the temperature of the rigid bar is -45 degrees celsius. A close fit exists at both of the rigid supports when the temperature is 24 degrees celsius. Use E= 68 GPa and Coefficient of thermal expansion is 11.7 x 10^-6 per degrees Celsius.
a) Determine the force P (in kN) required to stretch the Aluminum bar by 3mm. B) Determine the final width and thickness of the Aluminum bar. (1)
A truss system is supported by two pins at the top. Determine the absolute value of the axial stress in member AC (in MPa) if the diameter of the member is 30 mm.
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 520 mm?. If the stress in the bar must not exceed 650 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 8 m, b = 4.8 m, and c= 10.4 m. (1) B' a Answer: P = i kN
А P 200 mm В E 150 mm F Three steel (E=200 GPa) rods (AB, CD and EF) support a load of P=30 kN as shown in the figure. Each of the rods AB and CD has a 80-mm2 cross-sectional area and rod EF has a 120-mm2 cross-sectional area. (a) Write the equilibrium equation for the rigid member BED in vertical direction, (b) write the compatibility equation for the given bar system, (c) determine the force in rod EF (d) determine the average normal stress in rod EF.