The two baseband signals m1(t) and m2(t) are to be transmitted simultaneously Qver a channel by multiplexing scheme shown below. Sketch signal spectra at each indicated point, and what value of the carrier and filter H specification required to modulate m, (t) so that it is next to the spectrum of the signal at point R (upper or lower). Mi(f) W (t) x cin 1 6 HPF I PF

The two baseband signals m1(t) and m2(t) are to be transmitted simultaneously Qver a channel by multiplexing scheme shown below. Sketch signal spectra at each indicated point, and what value of the carrier and filter H specification required to modulate m, (t) so that it is next to the spectrum of the signal at point R (upper or lower). Mi(f) W (t) x cin 1 6 HPF I PF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q3. A baseband pulse position modulation (PPM) system uses signals si(t) and s2(1) shown below to represent bits 1 and 0, respectively. Find two orthonormal basis functions for these waveforms and write s (t) and s,(t) in terms of them. Sketch the signal space diagram of the transmitted signals and suggest a correlation type receiver to extract the data symbols in AWGN channel. Assume that T, represents the bit interval, A is the signal amplitude, and E, is the signal energy per bit. T/2 T/2
PM modulated signal is demodulated using: Select one: a. Costas PLL O b. Discriminator Oc. Discriminator followed by integrator O d. Carrier reinsertion method A PLL can be used for the generation of an in-phase carrier for the coherent demodulation of DSB-SC Select one: O True O False
• Determine PSD of a bipolar signal shape defined by t sinT 0st
Q1 (a) A carrier signal with frequency of fe = 10 Hz is modulated by two modulating signals V (t) = 7cos7m x 10't and Vmz (t) = 5cos5nx 10ºt. (1) Identify a suitable block diagram for generating the double side band suppressed carrier (DSBSC) using two balance modulators and other suitable components (ii) Derive the mathematical expression of the modulated signal showing all sidebands. (i) Illustrate and label the corresponding parameters and values of the modulated signal frequency spectrum. (iv) Calculate the total power used to transmit the modulated signal (given a resistor of 50 (2) (v) Illustrate the new frequency spectrum if a bandpass filter with a bandwidth of 27000Hz, centered at 101.25 x 104Hz used to filter the modulated signal of Q1 (a)(ii)
compute the IC SATURATION CURRENT IF BCE IS EQUAL TO 0.4V
7-18
ELECTRONIC ENG PLS
Question 3. The mathematical equation of an AM modulated signal is given as follows mA. Cos((w. + wm)t+ 2. mA. SAM (t) = A,Cos(w.t) + Cos((w. - wm)t 2 %3| Where A. = 30, m = 1, w. = 6000t, w. + Wm 7000TT, w. – Wm 5000 Find out the following > Message frequency (@m) > Power in the sidebands Sketch the spectrum of the modulated signal.
digital communicationA signal was represented using Bipolar RZ with a bandwidth of 40 kHz, then thebandwidth will be …………. If Bipolar NRZ was used.
-The modulating signal 2cos (2 π×103 t) is used to modulate a carrier signal 40cos (2 π×104t). Evaluate the modulation index, percentage modulation, frequency of side band components and their amplitudes .What is the bandwidth of a modulating signal.
In a pulse code modulated system, a quantizer is used with 128 uniform levels. If 120 kHz is the maximum frequenxy of the baseband signal, then what will be the minimum transmission bandwidth?
ii) A single sideband AM signal (SSB-SC) is given by s(t) = 10cos(11000 πt). The carrier signal is c(t) = 4cos(10000πt). Determine the modulating signal m(t).