The two bars are made of polystyrene, which has the stress-strain diagram shown in the figure below. The bars rupture simultaneously when the load P = 14.5 kN is applied. Assume that buckling does not occur. (Figure 1) (Figure 2) Part A Determine the cross-sectional area of bar BC. Express your answer to three significant figures and include the appropriate units. ABC = Value Units Submit Request Answer Figure < 1 of 2 Part B Determine the cross-sectional area of bar AB. Express your answer to three significant figures and include the appropriate units. 1.2 m OB HA ? 1 m A AB = Value Units Submit Request Answer

The two bars are made of polystyrene, which has the stress-strain diagram shown in the figure below. The bars rupture simultaneously when the load P = 14.5 kN is applied. Assume that buckling does not occur. (Figure 1) (Figure 2) Part A Determine the cross-sectional area of bar BC. Express your answer to three significant figures and include the appropriate units. ABC = Value Units Submit Request Answer Figure < 1 of 2 Part B Determine the cross-sectional area of bar AB. Express your answer to three significant figures and include the appropriate units. 1.2 m OB HA ? 1 m A AB = Value Units Submit Request Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ProbleT = - An aluminum bar has diameter d = 40 mm, shear modulus of elasticity G = 27 GPa, and torque T = 300 N.m. (a) Determine the maximum shear, tensile, and compressive stresses in the bar, and show these stresses on sketches of properly oriented stress elements. (b) Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements. |d=40 mm T= 300 N-m
1 The principal stresses at a point in an elastic material are 1.50 (tensile), o (tensile) and 0.50 (compressive). The elastic limit in tension is 210 MPa and μ = 0.3. What would be the value of o at failure when computed by different theories of failure.
Give me right solution with clear hand writing.
Urgent
1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
The overhead beam in the figure has the composite section given below. The bending moment vector acts at an angle of 0-60 degrees with the horizontal z-axis of the beam section as shown in the figure. Determine the stress at point K of the beam section for the maximum bending moment under the forces acting on the beam. Note: The numerical values of the relevant parameters are given in the attached table for each student. K Z< M 0 40mm 395 mm B2 40mm B1 240 mm + 45 mm H 180 mm 45 mm 32 KN -1.6 m B 2.4 m с 36 kN/m 6.4 m D
From the given illustration below, the force acting on B is equal to 25 kN, on C = 20 kN, and on D = 30 kN. If the cross sectional area of the material is 600 sg.mm, what is the maximum stress in the bar? FINAL EXAM 一- A B FINAL EXAM
Answer number 2 only
ANSWER THE PROBLEM GIVE WHAT IS ASKED, SHOW YOUR SOLUTION, AND BOX THE FINAL ANSWERS. WRITE IT ON A CLEAN PAPER CLEARLY. I WILL GIVE THE FEEDBACK RATING AS POSSIBLE, YOU CAN ANSWER IT. THANK YOU
ANSWER THE PROBLEM GIVE WHAT IS ASKED, SHOW YOUR SOLUTION, AND BOX THE FINAL ANSWERS. WRITE IT ON A CLEAN PAPER CLEARLY. I WILL GIVE THE FEEDBACK RATING AS POSSIBLE, YOU CAN ANSWER IT. THANK YOU
Your answer is incorrect. An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam areb1 = 35 mm, d1= 115 mm, b2= 21 mm, d2 = 21 mm, and a =7 mm. For this material, the allowable tensile bending stress is 15 MPa, and the allowable compressive bending stress is 14 MPa. Determine the largest moment M that can be %3D %3D %3D %3D %3D %3D applied as shown to the beam. b2 a 不 d2 d1 b1 Answer: N-m M% =
Wire BC has a diameter of 0.10 in. And its material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle D if the pull on the handle is slowly increased and reaches the magnitude of P = 655 lb. o (ksi) 40 pulg 80 70 B 50 pulg - 30 pulg € (pulg/pulg) 0.007 0.12