The tunnel exhausts to the ambient environment, where the back pressure is Patm. The starting stagnation temperature of the supply air is 300 K for all conditions, unless specified otherwise. PartB: Considering only tunnel Mach numbers of 1.5, 2 and 3, with test section cross-sectional areas of 6 x 6 in and 12 x 12 in and a diffuser divergence angle of 3°; calculate the following. 1. An angle of the sidewalls of the test section that would be required to keep the Mach number in the test section constant. Use a test section length of 2 times its height.

The tunnel exhausts to the ambient environment, where the back pressure is Patm. The starting stagnation temperature of the supply air is 300 K for all conditions, unless specified otherwise. PartB: Considering only tunnel Mach numbers of 1.5, 2 and 3, with test section cross-sectional areas of 6 x 6 in and 12 x 12 in and a diffuser divergence angle of 3°; calculate the following. 1. An angle of the sidewalls of the test section that would be required to keep the Mach number in the test section constant. Use a test section length of 2 times its height.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

b) In a converging-diverging duct the flow conditions are such that a normal shock is formed at the exit of the diverging section. Upstream of the shock the flow conditions are as below. Mach number= '0.5198', Pressure= '311886.9' Pa and Temperature= '228.72' K. Obtain the Mach number, pressure, and temperature at the downstream of the shock. Assume standard air properties (y=1.4).
A rocket motor is designed to give 10, 000 N thrust at 10, 000 m altitude. The combustion chamber pressure and temperature are 2 × 106 P a and 2800°K, respectively. The gases exit the combustion chamber through a Laval nozzle. Find the exit Mach number, and the cross-sectional areas of the exit and the throat of the nozzle. Assume the nozzle flow is isentropic and one-dimensional, and that the ratio of specific heats γ for the combustion gases is 1.32.
For an exhaust valve of 1.43 * 10-3 m? effective area, calculate the mass flow rate through the valve (SI unit). The flow coefficient is 0.65 and the cylinder pressure and temperature are 625 kPa and 820 K. Assume exhaust system pressure is 103 kPa, the specific heat ratio is 1.4 and R =287 J/ kg.K.
Solve it correctly please. I will rate accordingly.
HANDWRITTEN: Learjet 35 is a multi-role business jet and a military transport aircraft equipped with tail-mounted turbofan engines. This business jet has a cruising speed of 480 mph and cruising at an altitude of 45,000 ft. The ambient pressure and temperature is 390 R and 310 psfa, respectively. If the compressor has a pressure ratio of 18:1 and the maximum operating temperature is 2885 degrees Fahrenheit. Compute for the (a) compression ratio, (b) volume and temperature at each point, (c) Heat added and Heat rejected (d) Wnet (item c), (e) Brayton work (based on compressor and turbine work), and (f) efficiency. Note: Make sure to indicate a CORRECT P-V and T-S diagram
Problem 3 – Sparky needs helium for an experimental project. The helium is stored in a storage tank at 20°C and 300 kPa. The helium exits through a converging nozzle to the environment (100 kPa atmospheric pressure) and has 10 mm exit diameter. Determine the exit flow rate of the helium. Helium’s ratio of specific heats is 1.667. This is a compressible flow problem. Only use equations and tables from the textbook to solve this problem. Note the figures in the textbook and textbook appendices are based in air, not helium, and are not valid for this problem.
A converging-diverging nozzle is attached to a reservoir where the pressure is 718 kPa. The design exit Mach number is 2.9. What is the design exit pressure (in kPa)?