The triangle section AB beam, bearing the load F1 = 400 daN in the figure, is produced from a material with a maximum shear stress of 1800 dan / cm2. If the base length of this beam, which is forced to bend under F1 load, is b = 8 cm, how many cm should its height (h) be in order to carry this load 3 safely? (The weight o the beam will be neglected) %3D F1=400 dan 300 cm 100 cm 38 -

The triangle section AB beam, bearing the load F1 = 400 daN in the figure, is produced from a material with a maximum shear stress of 1800 dan / cm2. If the base length of this beam, which is forced to bend under F1 load, is b = 8 cm, how many cm should its height (h) be in order to carry this load 3 safely? (The weight o the beam will be neglected) %3D F1=400 dan 300 cm 100 cm 38 -

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P = 3000 Ib and the cross sectional area of the rod is 0.5 in^2, determine the stress in each section. Steel Bronze 4P | Aluminum | P 2 ft 3 ft 2.5 ft а. Stress (st) = 19 ksi, Stress (al) = 25 ksi O b. Stress (st) = 16.5 ksi, Stress (al) = 24.2 ksi O c. Stress (st) = 24 ksi, Stress (al) = 18 ksi O d. Stress (st) = 26 ksi, Stress (al) =17 ksi
Follow-up questions. Rate will be given! c. Calculate the maximum tensile stress in ksi. d. Calculate the angle that the neutral ads makes with the z axis in degrees.
Answer all.a.A mild steel flat of width b= 150 mm, thickness t = 20 mm and length L= 6000 mm carries an axial pull P = 300 kN. If modulus of elasticity of mild steel is 200 GPa and Poisson’s ratio is 0.25, calculate the change in length, width and thickness of the flat. B.A stepped bar made of brass is subjected to axial loads as shown in the below figure. Determine the total change in length of the bar. Take E =100 GPa.figure is attached C.A thin cylinder of external diameter 820 mm, length 3 m and wall thickness of 10 mm is subjected to an internal pressure of 2.5 N/mm2 . Determine the change in diameter and length. Take Young’s modulus = 2×105 N/mm2 and Poisson’s ratio = 0.25.
The AC beam given in the figure is subjected to a vertical force of 3 kN. Pull on AB bar the distance x required for the stress to be equal to the compressive stress occurring in the support C calculate. The cross-sectional area of the AB rod is 400 mm2 and the area of the support surface C is 650 mm2.
A 52-kip force acts on a machine part at point A as shown below. The diagram shows the internal normal force, shear force and bending moment acting on a particular RECTANGULAR Cross section. -30in N 10in 26in F=52 kip The value of the bending moment M you would use to find the bending stress on a stress element located 2 inches up from the bottom of the rectangular cross section is closest to: 264 kip-in O a. 408 kip-in Ob. 1,464 kip-in O c. 1,608 kip-in
Bronze Steel Steel W = 40 kips %3D 2 ft 2 ft 2.
The beam shown is made of a nylon for which the allowable stress is 24 MPa in tension and 30 MPa in compression. Determine the largest couple M that can be applied to the beam. M = N•m A 15 mm ✓ 56 mm 28 mm 30 mm M
An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm , 100мра C 240 MPa E=80GPa ✓=0.3 G=30GPa Answer = -0.5888mm
3 The piece of plastic is originally rectangular. Calculate the shear strain Yxy at corners A and B if the plastic distorts as shown by the dashed lines. 2 mm 300 mm 2 mm D -400 mm- mm, B A 4 mm 72 mm 3 mm X
A wood beam is strengthened using two steel plates as shown in the figure below. V 6 mm 150 mm 6 mm |B 100 mm i The beam has simple supports and an overhang and is subjected to a point load and a uniform load as shown in the figure below. 13 KN q= 5.0 kN/m с 3 m Calculate the maximum tensile and compressive stresses of the beam. Assume that E = 11 GPa and E = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention.) maximum tensile stress in wood MPa maximum tensile stress in steel MPa MPa maximum compressive stress in wood maximum compressive stress in steel MPa Need Help? Read It B 000 +1m-
Consider the timber beam shown below. The beam is made out of southern yellow pine, with an allowable bending stress of ?all= 2700 psi. The modulus of elasticity is E = 2,400 ksi. The maximum allowable deflection in the beam is 0.25 inches. A 1.5 kip/ft 6 ft 4 in. h B (a) What are the boundary conditions for this beam? (b) Determine the equation for the moment diagram using statics. (c) Determine the depth of the beam necessary to meet the allowable bending stress requirement.
Icles Current Attempt in Progress A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain yy at P. Assume a = 1190 mm, b = 590 mm, c = 1.1 mm, and d = 0.8 mm. R Answer: Shear strain yy prad. %D