The transistors in the circuit below have 3 =100 and VA = 50 V. The biasing current sources are equal: I₁ = I₂ = 0.2mA Find Rin and the overall voltage gain. Round your answer to three significant digits. Rin= type your answer... ΜΩ Av = type your answer... V/V Rs Vs + = 500kΩ Rin +5V Q₁ ½₁ D↓½₂ Q2 Vo

The transistors in the circuit below have 3 =100 and VA = 50 V. The biasing current sources are equal: I₁ = I₂ = 0.2mA Find Rin and the overall voltage gain. Round your answer to three significant digits. Rin= type your answer... ΜΩ Av = type your answer... V/V Rs Vs + = 500kΩ Rin +5V Q₁ ½₁ D↓½₂ Q2 Vo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit given in the figure | VBE | = 0.7V, R1 = 11.06Kohm, R2 = 48.24Kohm, RC = 1.03Kohm, RE = 3.09Kohm, VCC = -13.00V, Beta = 150.00, calculate the IC current by full analysis.
Answer question
Please answer fast I'll rate
NPN BJTs can be used as emitter followers. In the given circuit, the follower is connected to a non-ideal voltage source (Vs) with a source resistance (Rs) What should be the value of Vs for the BJT to start saturating of Rs = 5k ohms.
Q-2: Explain the saturation of a transistor. Find the given unknowns for the figure below. a. Rc. b. Rg c. Rp. d. VCE e. V Also find the voltage V, at cutoff. 12 V 2 mA Rc 7.6 V V B-80 024 V Q-3: Define Lso and lao, How are they related? Find the following f le corresponding to V = +750mv and Va = +5V
What output voltage results in the circuit below for an input of 0.5 V. Refer to the following for the values of Rf = 413981 ohms, R1 = 16788 ohms. Express your answer up to two decimal places. ... V. 360 kQ 12 ko Round your answer to 2 decimal places.
In a N-Channel JFET if the voltage across the drain and source (VDs) is increased then explain in detail with neat diagram the changes in drain current. Justify your answer.
In the circuit given in the figure | VBE | = 0.7V, R1 = 11.06Kohm, R2 = 48.24Kohm, RC = 1.03Kohm, RE = 3.09Kohm, VCC = -13.00V, Beta = 150.00, calculate the IC current by full analysis.
First，Calculate the input resistance Rin defined as Vin/Iin . Hint: Assuming you know the variable Vin, find Iin in terms of Vin. Substitute Iin into Vin/Iin, then variables Vin will cancel each other on the numerator and denominator. You will get a number that represents Rin. Second，Construct the resistive network in figure 5 with Vin = 5V from the Arduino POWER section. Measure Vin. Then, measure Iin by inserting the DMM between node n1 and n2. Divide these two values to get Rin. Report Vin, Iin, and Rin. Then， Are the measured input resistance values the same when you use Vin = 3.3V and when you use Vin = 5V? Is Rin independent from Vin and Iin? Explain it. Also, include a photo of your circuit！
I need to design a power supply 110v , with an output between 6 and 9v. I did a design and I implemented a resistor after the bridge as a surge protector for the diode. I need to know if this is the right design and I need some calculations for the elements to provide an output between 6 and 9v.