The transfer function of a position control system is given by:Determine:a) TpC(s)R(s)b) %μs c) T, and=15002s² +55s + 1500d) T, for a ± 2% band

By using the given standard transfer function we have to calculate the values of time domain…

Answered: The transfer function of a position…

The transfer function of a position control system is given by: Determine: a) Tp C(s) 1500 R(s) 2s² +55s +1500 = b) %μs c) T, and d) T, for a ± 2% band

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

mld=26287&page%3D6 a signal x(t) = – sinc(-) is applied to the system shown in i then the spectrum of the system output is to be : on x(t) d y(t) dt Select one: Y (@) = rect(@)/j@ Oa. %3D O b. Y (w) = jwrect(@) OY(@) = -jwrect(@ – 2) O a. Y(@) = jwrect(@) + n8(@) %3D 05:12 EN - E - 0 DELL 8808888-88-88-8 Ingert F11 F12 F10 F6
ASAP It is a type of diode where it operates as a variable resistor when heated. Your answer What is the modulation index in ideal condition of AM. Your answer A form of AM where a sideband is filtered after its carrier is eliminated. Your answer What is the form of AM that used to transmit video signals of the TV system? Your answer It is a circuit in the superheterodyne receiver that adds and subtracts the frequencies of the AM signal and the local oscillator frequency. It is the extent to which the amplitude of the carrier wave is varied by modulating wave.
A sinusoid signal v(n) = 5 sin( @₂ .n) with f=5 Hz and fs = 10 kHz has to be quantized @ (Vq(n) = Q[v(n)]) with a midtreat quantizer. The range of the signal is ±5 V and the word length of the quantizer 4 bits. The quantizer is at digital full scale. (a) How many quantization levels L does the quantizer have? What is the value of A? (b) Sketch the input-output characteristic of the quantizer. How different is a midtreat quantizer to a midrise quantizer. (c) For time index n = 1250 calculate the quantized value v₁ (n), the quantization error eq(n) and represent vą (n) using RZ code. (d) Calculate the power P of the quantization noise. (e) Determine the SNR in dB.
Example: Suppose that an analog signal is given as x(t) = Scos (27 x 103t) and is sampled at the rate 8kHz. Sketch the spectrum for the original signal and the sampled signal from 0 to 20kHz. I need the solution step by step and clear line please
Please I need the answer as soon as possible pleeeeeeeaasse in short answer
2) A voltage signal consists of the following periodical waveform: V(t) = 10 sin 502.7t + 5 sin 94.2t + 15 sin 942.5t where t is in seconds and Vin volts. This signal is sampled digitally at a sampling frequency of 200 Hz. 128 data points are taken. a) Recommend additional procedures to sample the signal properly in the frequency domain considering the sampling conditions given above. b) Sketch what the frequency spectrum would look like if you were to perform an FFT on these sampled data. Label your axes carefully. c) Calculate: - the total sampling time - the time increment between sampled data points - the frequency resolution of the frequency spectrum - the Nyquist frequency
x(+) = cos (10Tt) AAA. Sample the above signal for, a) fs = 5 Hz b) fs = l0 Hz Can x(4) be obtained from sampled signals without loss ? %3D %3D
What is output signal when a signal x(t)=cos(2*pi*40*t) is sampled with a sampling frequency of 20HZ? a) cos(pi*n) b) cos(2*pi*n) c) cos(4*pi*n) d) cos(8*pi*n)
I need the answer as soon as possible
it in B- Consider the analog signal x(t) What is the Nyquist rate for this signal? 3cos50 mt + 10sin100 nt + cos150 nt Choose one C
Find the transient current (a general solution) in the RLC-circuit in the figure below for the given data. R = 6 N, L = 0.2 H, C = 0.025 F, E = 190 sin (10t) V R E(t) = E, sinot Write arbitrary constants as C1 and C2. ll
you design differentiator to differentiate input signal varies in frequency between 1 KHz and 20 KHz then find , If a sine wave of (0.1v) peak at 10KHZ is applied to the differentiator designed above then the output voltage will be if ...... cos (2n (10) ^4 t] 1-O cos (2n (10] ^4 t] 10 cos (2n (10) ^4 t] 1.5-O cos (2n [10] ^4 t] 1.50