The torsional spring at A has a stiffness ky-19 Nm/rad and is undeformed when the uniform 17-kg bars OA and AB are in the vertical position and overlap. If the system is released from rest with @-69, determine the magnitude of the angular velocity of wheel 8 when 9-32. The 13-kg wheel at B has a centroidal radius of gyration of 60 mm and is observed to roll without slipping on the horizontal surface. 775 mm 775 mm -80 mm

The torsional spring at A has a stiffness ky-19 Nm/rad and is undeformed when the uniform 17-kg bars OA and AB are in the vertical position and overlap. If the system is released from rest with @-69, determine the magnitude of the angular velocity of wheel 8 when 9-32. The 13-kg wheel at B has a centroidal radius of gyration of 60 mm and is observed to roll without slipping on the horizontal surface. 775 mm 775 mm -80 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 29-kg spool of outer radius ro=530 mm has a centroidal radius of gyration k=355 mm and a central shaft of radius ri=215 mm. The spool is at rest on the incline when a tension T=204 N is applied to the end of a cable which is wrapped securely around the central shaft as shown. Determine the acceleration aaa of the spool center GGG and the friction force FFF acting at the interface of the spool and incline. The friction coefficients there are μs=0.28 and μk=0.17. The tension T is applied parallel to the incline and the angle θ=16. The acceleration aaa and the force F are both positive if up the incline, negative if down.
SOLVE USING PRINCIPLE OF WORK AND ENERGY
The shown spool has a mass of 450 kg and aradius of gyration Gk=1.2 m. It rests on thesurface of conveyer belt for which the coefficient offriction m= 0.5. If the conveyer acceleratesat2 1.2m / S and the spools rolls without slipping,determine the tension in the wire and the angularacceleration of the spool
The 3.8 kg block is descending at a rate of 1.2 m/s when the hydraulic cylinder BC exerts a force F=500 N on the brake arm. Determine the number of radians the wheel will rotate before the system comes to rest. The wheel has a mass of 25 kg and a radius of gyration about its center kO=300 mm. The coefficient of kinetic friction between the brake arm and the wheel is 0.25.
The slotted circular disk whose mass is 4.9 kg has a radius of gyration about O of 230 mm. The disk carries the four steel balls, each of mass 0.17 kg and located as shown, and rotates freely about a vertical axis through O with an angular speed of 164 rev/min. Each of the small balls is held in place by a latching device not shown. If the balls are released while the disk is rotating and come to rest relative to the disk at the outer ends of the slots, compute the new angular speed N of the disk. Also find the magnitude |AE| of the energy loss due to the impact of the balls with the ends of the slots. Neglect the diameter of the balls and discuss this approximation. 164 rev/min 145 mm 305 mm
*17-76. The 20-kg roll of paper has a radius of gyration ka = 120 mm about an axis passing through point A. It is pin supported at both ends by two brackets AB. The roll rests on the floor, for which the coefficient of kinetic friction is Hk = 0.2. If a horizontal force F = 60 N is applied to the end of the paper, determine the initial angular acceleration of the roll as the paper unrolls. 300 mm/ 400 mm
The system is made up of the 1-m, 6.7-kg uniform rod AB and the two uniform disks (each of 0.10 m radius and 2.2 kg mass). If the system is released from rest when 0- 55", when rod AB has just become horizontal, determine the angular velocity of rod ABin rad/s. Assume the disks roll without slipping. Your answer must include 2 places after the decimal point. Please pay attention: the numbers may change since they are randomized. Take g= 9.81 m/s?. 1m
The uniform 80 kg slender rod is at rest in the position shown when P = 450 N is applied. Determine the value of angular velocity, w2 the rod if L1 = 5.5 m and L2 = 6.5 m. A L L2 L1 B
The speed of the pickup truck’s engine is controlled by the Porter governor with4 arms of equal length, and pivot on the axis of rotation. Each ball has a massof 4 kg and the mass of the central load on the sleeve is 20 kg. The radius ofrotation of the ball is 150 mm when the governor begins to lift, and 200 mm whenthe governor is at maximum speed. The initial angular speed of the engine’scrank is 14 rad/s, and it has reached a maximum speed at an acceleration of 0.4rad/s2 after 5 seconds. 2.1. If the speed of the crank of an engine is equal to the speed of its governor,calculate the angle between the upper arm and axis of rotation (?) when thegovernor starts to lift and when it is at maximum speed.(11)2.2. Prove that the length of the governor’s arms is equal.
The 15 kg pendulum shown has its mass center at G and a radius of gyration about its mass center of kG = 200 mm and was released from rest when 0 = 0°. Spring AB has a stiffness of k = 200 N/m and is un-stretched when 0 = 90°. The angular velocity of the pendulum in rad/s at the instant 0 = 90° is: -0.6 m- а, 3.2 · b. 4.3 m . с. 3.6 0.1 m · d. 4.4 О е. 3.4 O f. 3.8 O g. 4.6
Please don't provide handwritten solution....
The circular disk of 145-mm radius has a mass of 38 kg with centroidal radius of gyration k bar = 25 mm and has a concentric circular groove of 55-mm radius cut into it. A steady force Tis applied at an angle theta to a cord wrapped around the groove as shown. If T = 40 N, theta = 0, mu_s = 0.11, and mu_k = 0.09, determine the angular acceleration a of the