The top width and the depth of flow in a triangular channel were measured as 4 m and 1 m, respectively. The measured velocities on the centre line at the water surface. 0.2 in and 0.8 m below the surface are 0.7 m/s, 0.6 m/s and 0.4 m/s respectively. Using two-point method of velocity measurement, the discharge (in m³/s) in the channel is

The top width and the depth of flow in a triangular channel were measured as 4 m and 1 m, respectively. The measured velocities on the centre line at the water surface. 0.2 in and 0.8 m below the surface are 0.7 m/s, 0.6 m/s and 0.4 m/s respectively. Using two-point method of velocity measurement, the discharge (in m³/s) in the channel is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A B E 0.40Qgc
A right-angled triangular notch is used for gauging the flow of a 140 cm wide, laboratory flume. In observing the head, a reading of 64mm was observed. Water passing over the weir drains into the basin of the hydraulic rig. 45cm in length and 30cm in width. At constant head, it took 27 seconds to fill a depth of 29cm in the basin. Actual discharge in the flume in cubic meter per second ? Theoretical discharge in the flume in cubic meter per second ? Compute for the coefficient of discharge of the notch
Please solve accurate and exact please thisnis important
.
(7) (8) Water flows in a rectangular channel with base width B=5 m and depth D=1.5 m. It then flows under a sluice gate that has a width equal to that of the channel base and is raised so that the depth of flow under the gate is d-0.5 m. Calculate the flow rate in the channel and the force on the sluice gate Downstream of the sluice gate in question (7) there is a hydraulic jump. Calculate the downstream depth of flow and the head loss in the jump.
) Water is flowing in a 150mm uniform diameter pipe installed in a vertical plane shown in Figure 4. The pitot tube is connected to the piezometric tube. The total head loss from point 1 to 2 is 2.3 times the velocity head of flow in the pipe. Calculate the flow rate in the pipe. sg = 0.82 856 mm h Figure 4
For the pipe network given in the figure, the pipe flow rates in the intermediate lines, the given initial values Calculate using the Hardy-Cross Method. (Take the coefficient of friction on all lines f = 0.002 and perform two iterations.) Hat no 1 2 3 4 5 150 lt/s Q (It/s) 100 50 10 75 15 2 L (m) 300 300 200 250 150 3 35 lt/s 25 lt/s D (mm) 100 125 150 125 200 t 10 90 lt/s
Question number 7
Water is flowing in a rectangular channel that has a width b=3 m. If the depth of flow y = 2 m and Froud Number NF=3.3, then the flow rate(Q) in the channel is
for pipe flows for given pipe lengths (m) and pipe diameters (mm). Initial flow as shown in the table. Determine the correct flow rate in each pipe to A< 0.0009. Assume a constant The pipe network of two loops as shown below has to be analyzed by Hardy Cross method friction factorf=0.02. 0.4m /sec 0.3m³ /sec Pipe No. Q (m³/sec) 1500 m 0.718 500 тm 1 0.282 3000 m 300 тm 2500 mm 3 0.084 2500 m 2) 500 mm 400mm 3 0.066 0.334 1500m 600mm 0.3m³ /sec 1m /sec 2. 4.
2. The diameter of a 3 meter pipe decreases from 450 mm to 150 mm. If the velocity is to decrease uniformly in a linear manner, draw the diameter profile at each 500 mm length interval along the pipe. Discharge is 150 liters per second.
Quick