The TLC plates below show authentic samples of salicylic acid in the left lane and student product in the right lane. The plate on the left was run in 50:50 hexane:ethyl acetate, and the plate on the right was run in 50:50 hexane:ethyl acetate plus a single drop of acetic acid in the solvent. Calculate the Rf of salicylic acid on the LEFT-HAND PLATE ONLY. Report your answer to two significant figures.

The TLC plates below show authentic samples of salicylic acid in the left lane and student product in the right lane. The plate on the left was run in 50:50 hexane:ethyl acetate, and the plate on the right was run in 50:50 hexane:ethyl acetate plus a single drop of acetic acid in the solvent. Calculate the Rf of salicylic acid on the LEFT-HAND PLATE ONLY. Report your answer to two significant figures.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

In normal phase TLC, the mobile phase is + polar than the stationary phase. Consider the TLC plate below, which was developed using a 25% ethyl acetate:hexane solution. If this same mixture of compounds was developed on a TLC using a 50% ethyl acetate:hexane solution, the orange spot would A mixture of two compounds was developed on a TLC plate. The result is shown below. What is one thing the chemist can do to get better results? In normal phase TLC, the mobile phase is : polar than the stationary phase. Consider the TLC plate below, which was c exane solution. If this same mixture of compounds was developed on a TLC using a 50% ethyl acetate:hexane solution, the orange spot would less sometimes more, sometimes less more A mixture of two compounds was developed on a TLC plate. The result is shown below. What is one thing the chemist can do to get better results?
Three labs were contracted to measure the concentration of a 5.50 ppm Ca2* standard solution. They each measured the solution 3 times, and their results are as follows: Measurement 1 Measurement 2 Measurement 3 Laboratory 1 5.47 ppm 5.54 ppm 5.50 ppm Laboratory 2 5.32 ppm 5.44 ppm 5.56 ppm Laboratory 3 5.61 ppm 5.62 ppm 5.60 ppm Select ALL of the TRUE statements about the measurement capabilities of these labs. Lab #3 was the most precise. Lab #1 was the most precise. Lab #1 was the most accurate. Lab #2 was the most precise. O.Lab #2 was the most accurate. Lab #3 was the most accurate.
In a particular trial, a student got a value for R of 0.083. Calculate the percent deviation of this result. Enter a number without the % sign. The percent deviation should be reported as a positive value.
Which is correct? Random errors affect accuracy and systematic errors affect precision. An accurate result shows agreement with the true or accepted value. Precise results can contain significant random error, but little systematic error. The standard deviation is a good measure of accuracy. Polydimethylsiloxane (PDMS) stationary phases have low polarities. Which of the following statements is TRUE about gas chromatography using PDMS stationary phases? The gas chromatography column is typically packed with silica microparticles. An oven is used to control the column temperature because a constant temperature is always needed in gas chromatography Octane (C8H18, boiling point: 126 ºC) is eluted later than dodecane (C12H26, boiling point: 216 ºC) 3-Pentanone ((C2H5)2CO, boiling point: 102 ºC) is eluted later than propanol (CH3CH2CH2OH, boiling point: 97 ºC)
Often the analyst will compare known quantities of analyte to unknown quantities of the material to be analyzed. This may be done in one of three ways: -use calibration curves; use standard additions; or use internal standards. The method of standard additions would be used when A) the quantity of sample analyzed or the instrument response varies from run to run. B) the standard solutions and the unknown solution all have similar characteristics are unaffected by the other material in the sample. C) the sample composition is unknown or complex and affects the analytical signal.
A student obtains 0.95 g of crude 9-fluorenone and performs a recrystallization in cyclohexane (13 mL per 1 g crude 9-fluorenone). If the student recovered 0.57 of pure 9-fluorenone, what was the percent recovery of the recrystallization? Report your answer to no decimal places. Your Answer: Answer
10 mL of a liquid composed only of carbon and hydrogen is added to a separatory funnel containing 100 mL of water and 100 mL of hexane, an organic solvent. After shaking, the liquids are transferred to graduated cylinders. What are the volumes of the aqueous and organic layers? Aqueous 105 mL; organic 105 mL Aqueous 100 mL; organic 110 mL Aqueous 110 mL; organic 100 mL Cannot be determined O O O O
Need help on finding the yield based on data/experiment.
Convert ppm to mM and meq/L
10. An unknown compound is analyzed gravimetrically and found to contain 77.6 ± 0.1 % of bromine. You know the initial compound could be the bromide salt of sodium, potassium or calcium. Determine the molecular formula of the initial unknown salt. Show your work.