The three-step pulley shown in the Figure is subjected tothe given couples. Compute the value of the resultantcouple and determine the forces acting at the rim of themiddle pulley that are required to balance the givensystem. Consider A = 120 N.150 NA200N200N30 amA40 Cm150NSelect the correct response(s):233.33 N6100 N.cm clockwise6400 N.cm counter-clockwise6100 N.cm counter-clockwise223.33 N6400 N.cm clockwise 150 N200N200N30 amA40Cm150HSelect the correct response(s):233.33 N6100 N.cm clockwise6400 N.cm counter-clockwise6100 N.cm counter-clockwise223.33 N6400 N.cm clockwise203.33 N213.33 N

Given: Force A is 120 N. Consider the figure,

The three-step pulley shown in the Figure is subjected to the given couples. Compute the value of the resultant couple and determine the forces acting at the rim of the middle pulley that are required to balance the given system. Consider A = 120 N. 150 N A, 200N 200N 30 am 40 Cm 150N

The three-step pulley shown in the Figure is subjected to the given couples. Compute the value of the resultant couple and determine the forces acting at the rim of the middle pulley that are required to balance the given system. Consider A = 120 N. 150 N A, 200N 200N 30 am 40 Cm 150N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3.5 m A C 5.5 m 0.2 m B D G In the figure above, the jib crane is supported by a pin at C and rod AB. Knowing that x = 6.2 m, and the load D has a mass of 3050 kg, with its center of mass located at G, you are required to explain your answers by your own words and A) Draw the free body diagram (FBD) B) Determine the reactions at the pin C C) Determine the force developed in rod AB D) Check the equilibrium of the system by determining the sum of the moments of all forces about point B
The beam shown in the figure is supported at roller A and pinned at B and has a uniformly distributed loading w 36 kN/m over 1.5 m from the left-hand end and moment loading M = 44 kNm at 1.5 m from end B. - Determine the reaction force at support A. Input your answer as a value only in KN to one decimal place and without +/- sign. w kN/m M kNm B A X -1.5 m -1.5 m -1.5 m-
load A =350 N load b=400 N
The simply supported beam AB is loaded as shown in the figure below. 1. Derive the shear force and bending moment equations for the entire beam. 2. Draw the shear force and the bending moment diagrams based on the equations derived in part 1. A 2 m. 800 N/m 3 m 4.2 kN.m 2 m2 m→ B
only HANDWRITTEN answer needed ( NOT TYPED)
The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 190 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.8 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 1.6 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 39° x m 6 KN -2.5 m 1.5 m Questions: (a) If x= 1.6 m, R= (b) If x= 3.3 m, R = i (c) The minimum value for R = i (d) The pin should be designed to hold i KN KN kN at x = kN. i
Beam AB is loadead as shown. If P is 1000 lb, Solve for the ff: • Horizontal support reaction at A and B • Vertical support reaction at A and B Include 4 decimal points in all answers.
Consider the beam shown in (Figure 1). EIEI is a constant. Suppose that www = 19 kN/mkN/m.
Consider the compound beam shown in (Figure 1). Assume C is a roller, B is a pin, and A is fixed. Suppose that w = 16.5 kN/m Figure 3 m B 6 m < 1 of 1 Determine the moment of reaction at A. Express your answer to three significant figures and include the appropriate units. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. MA = Submit Part D • Nc = μA 1 D Value Request Answer Determine the normal reaction at the support C. Express your answer to three significant figures and include the appropriate units. μA Value Units 1 @ Units Review ? Your device needs to restart to install update
3.5 m A C 5.5 m 0.2 m B D G In the figure above, the jib crane is supported by a pin at C and rod AB. Knowing that x = 6.2 m, and the load D has a mass of 3050 kg, with its center of mass located at G, you are required to explain your answers by your own words and A) Draw the free body diagram (FBD) B) Determine the reactions at the pin C C) Determine the force developed in rod AB D) Check the equilibrium of the system by determining the sum of the moments of all forces about point B
C6 please help me with the answer and full solution