All the tension/compression members of the frame structure shown in the figure are pin-jointed and of equal length and negligible weight. An external load P = 34.7 KN is applied vertically at joint E. The frame is pin-connected at fixed support A and supported by a roller at D. What is the force in member AE? Input your answer as a value only in KN to one decimal place without +/- sign. L A

All the tension/compression members of the frame structure shown in the figure are pin-jointed and of equal length and negligible weight. An external load P = 34.7 KN is applied vertically at joint E. The frame is pin-connected at fixed support A and supported by a roller at D. What is the force in member AE? Input your answer as a value only in KN to one decimal place without +/- sign. L A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure below shows a uniformly tapering bar of rectangular cross-section of length L and thickness t. The width of the bar at one end is b₁ and the width at the other end is b2, where (b₂> b₁). The bar is subjected to an axial force P. The axial deformation due to load P is given by _mm. b₂ PL atE b₁ = 20 mm b₂-40 mm -In () then the value of (a + c) is
A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15900 ksi] rods, and a solid steel [E = 30300 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.69 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.42 in. Assume L=37 in and L2=68 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 28 kips is applied. (1) L2 (1) B P. Answers: i 27.744 ksi. 02 = 4.512 ksi.
e) the value of the constant of integration C2. Enter your answer in kNm3 to 3 decimal places.
The force in DB of the truss shown in below figure is W 5m 2W 5m W B. O 5 W tension O vW tension 2 W compression O v3 W compression
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 470 mm tw = 14 mm d = 120 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3330 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 428040000 mm4. If the beam will be subjected to a shear force of V = 225 kN, determine the shear stress at point H, located at yH = 110 mm above the z centroidal axis.
Please provide solution for this query
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 2.6 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at C. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1m
2. Resolve the vector force into its components in the Figure shown. * Z 2m F=80 kN 5m 3m
Determine the force in members BC, GA, and BG of the truss shown in the figure below. Let P = 175 kN. NOTE: If your answer is a compressive force then just put a negative sign. If your answer is a tensile force then just type the answer directly. (ALSO, DON'T FORGET THE UNITS) 2P 2P 30 60V60° 60°V60° C 30 D 3P 4m 4m 4m Solve the force in member BC. Solve the force in member GA. Solve the force in member BG.
A rigid bar, pined at point O, is supported by two heavy springs as shown in the figure. Considering the curvature of the spring, determine the maximum load W that may be supported if the shearing stress is limited to 140 MPa. n = 12 d = 20 mm D = 100 mm P₁ = P₂ = W = 0.60 m Required Values: (Units in N) -1.20 m 4 www n = 20 d = 25 mm D = 150 mm 0.90 m W
600 lb 600 lb Do 600 lb 300 lb B 300 lb 6 ft F H ΑΠ C E G 6 ft 8 ft -8 ft 8 ft 8 ft 8 ft→ Analyze the truss, find forces in all elements, use any methods
The beam section given in the figure is under the influence of M = 5 kN.m bending moment. Section C and B ' Calculate the normal stresses that will occur at the points. E = 200 GPa. (N-A axis weight passes through the center.)