The three bars are made of steel and form a pin-connected truss. Each bar has a cross sectional area of 3 in^2. Use Est = 29x10^6 psi. If the truss was constructed at 50 F and is heated to 110 F, coefficient of thermal expansion of steel = 6.6x10^-6 ft/ft F. Determine the following: a) Force in bar AD (kip) b) Force in bar AB (kip)

Q: P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

A:

Q: The bars AB, CD and EF made of material with E=180 GPa and have a cross sectional area of 678 mm2.…

A: P=163N A=678mm2 E=180GPa

Q: Please explain all question and draw diagram

A: Part 1. Calculate the displacements at the jointsGiven InformationThe truss structure is square with…

Q: -30-mm diameter 250 mm -50-mm diameter 300 mm C

A:

Q: 14. A steel column carries an axial load of 800 kN and a moment of 69 kN-m at the top and moment at…

A: f (bending stress ) = M/Sx {M in Nmm & Sx in mm3 } M = 69KNm = 69 x 106 (maximum moment) Sx =…

Q: The total pressure or pressure intensity is not zero for any point on inclined surface in space.

A: Total pressure, F=w*a*ŷ In space, w=0 as g=0 Hence, F=0. Hence, pressure intensity is zero at any…

Q: A structural beam subjected to sagging bending has a cross section which is an unsymmetrical I…

A:

Q: The beam cross section shown below has been proposed for a short pedestrian bridge.  The cross…

A:

Q: In the truss shown, A =1000 mm2, E = 200 GPa and the coefficient of thermal expansion is 12 x10…

A: Given Data: A = 1000 mm2E=200 Gpa   = 200×103 MpaCofficient of thermal expansionα=12×10-6/°CTo…

Q: Use Virtual Work Method to answer the questions below considering the truss shown in the figure.…

A:

Q: Question 2: calculate the forces in AB, BC and AC of the following Truss R kN R = Last two digits of…

A: R=6kN

Q: PROBLEM 4: Find the elongation in a 2m long steel bar by subjecting it to 40 MPa stress. E = 200 GPa…

A: Given-  Length of the steel rod (L) = 2m = 2000mm Stress in steel rod (σ) = 40MPa E= 200GPa=…

Q: 3. The tensile member shown, 60 mm x 90 mm in cross section is subjected to a load P=300 kN. The…

A: Solution Given Data: P= 300 KN Cross-section area A=(60mm×90mm) Angle with horizontal axis= 140

Q: For the truss shown in the following figure, the temperature of member BC is raised by 140 °C, and…

A:

Q: Determine the axial stress acting on a circular column. *

A: Axial Stress- Axial stresses are those which are responsible for bringing a change to the length of…

Q: 3. The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: Given: Support A : Hinged Support C: Roller Length of AB = 11 m Length of AC = 5 m Mass, M=260 kg…

Q: Consider a tetrahedron containing point Q and show the forces on the faces of the tetrahedron due to…

A: we consider a small element at point P whose shape is that of a tetrahedron. The three sides of the…

Q: A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an…

A: Detailed solution is provided below :

Q: re welded to a rectangular web plate. Dimensions of the cross section are: = 430 mm = 16 mm = 110 mm…

A:

Q: Below is another BA bar attached to the AD bar. Diameter of DA bar is 0.02M. A force F = 1000N is…

A:

Q: The 3 bars are made of steel and form a pin-connected truss. Each bar has a cross sectional area of…

A:

Q: For an element subjected to ox = 40 MPa (compressive), oy = 30 MPa (tensile) and txy = +20 MPa, the…

A:

Q: A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm,…

A: Given data :We have to calculate the elongation of the bar

Q: A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of a cast iron 5 mm thick.…

A:

Q: 1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A:

Q: Three round bars welded together are axially loaded as shown. Find the normal stress in each bar if…

A:

Q: The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be…

A: we have to determine the maximum load P

Q: What is the maximum allowable force P in lbs?

A:

Q: mm 0OST 150 mm 700 mm 80 mm

A: Given, b=1500 mm Web width bw=280 mm h=700 mm Flange thickness tf=150 mm fc'= 42 MPan=7.85 fy = 380…

Q: 2) The rigid bar ABC is horizontal before the load Pis applied as shown in the figure. Determine the…

A:

Q: The bar AB is attached to aluminum and steel rods, horizontal before the load P is applied. Find the…

A: We will find force in Aluminium and use displacement formula.

Q: The 1154-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 424…

A: Given,The cross-sectional area for AC and BD is,A=424 mm2The stress in cable AC is,σAC = 148 MPaThe…

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.