The thin ring can be adjusted vertically between three equally long cables from which the 138-kg chandelier is suspended. If the ring remains in the horizontal plane and

Q: Date: 5 meter long by I meter wide slanted gate has a at point e CkN) reguired to keep the gate…

A:

Q: • Determine deflection at D. B and D are both internal hinge E- 2006R I- 200 u men 15 KN/m 5

A:

Q: Q.7 For the piping system shown in figure (EI) A=10" N-cm' and (El)RC =8x10" N-cm2 The axial…

A: Given:- A piping system is shown  The magnitude of the force at point B = FB = 5375 N  The value of…

Q: zero force member? C E В 4 m H F A 3mV 3m. 3m 80 kN 120 kN

A: Free body diagram At, joint A,F& D

Q: Four people are attempting to move a stage plat- form across the floor. If they exert the horisontal…

A: To find equivalent couple force at O

Q: What is the deflection at the hinge for the beam shown below? A C I B I L/2 – L/2

A:

Q: A system of cables is shown and in a state of equilibrium. Using equilibrium equations, solve for…

A:

Q: Draw the influence line for LH and LM

A: Data given Find : Influence line diagram ( ILD )for member LH and LM

Q: Use the method of virtual work to determine the tension in cable AC. The lamp weighs 10 lb.

A: Draw FBD:

Q: The machine part of negligible weight is supported by a pin at A and a roller at C. Determine the…

A:

Q: Determine the tension developed in each cord required for equilibrium of the 20-kg lamp.

A: Given : lamp weight = 20 kg To Find : Tension developed in each cord?

Q: 3-59. Determine the tension developed in the three cables required to support the traffic light,…

A: Given data  m = 20kg  h =3.5m

Q: Determine the angle (0) between cables AB and AC. 4 m A 2 m 3 m 2 m 3 m 3 m

A:

Q: 3.6 A 4-m-long rigid body carrying a 10-kN/m uniformly distributed load is supported by a pinned…

A: given data is length of bar=4m to find the free body diagram and the reaction force at A also to…

Q: 3 - 33 The lamp has a weight of 15lb and is supported by the six cords connected together as shown.…

A: Given : Weight of lamp = 15 lb To Find : Determine the tension in each cord and angle Thetha for…

Q: Determine the forces acting on all  specified pin connections of the frame (pts A, B, & D)

A: To find pin reaction at A, B, D

Q: 8) A shaft of diameter (d 5-mm) is to be pulled through a (4.5)-cm-diameter glycerin-filled sleeve…

A:

Q: HiW. Find the deflection distribution dingram For the following laaded beam. lON 10 Cm 5 m 5 Cm…

A:

Q: gular acceleration ac of the cables. C

A:

Q: base line was measured in catenary in four lengths giving 30.126, 29.973, 30.066, and 22.536 meters.…

A: As per guidelines we need to answer only first 3 subparts of question so please repost rest…

Q: What is the type ofsupport A 400 N/m 200 N/m 4m - 3m -

A: (c) Pin is the type of  support A

Q: Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE!

A: We will use diagram to find force and distance from C .

Q: Replace the system of forces acting on the frame in the figure by a resultant R at A and a couple…

A:

Q: Determine the moment about point A and then B A 300 mm 30° F

A: Following are the given information. d=300 mm F=200 N

Q: Analyze the loaded cables as shown.

A: Step: 1 Cable structures: - It is defined as the structures in which cables are used as main load…

Q: 500 N 400 N 500 N 250 N 250 N 30 G. 60 30 30 5 m 5 m

A:

Q: 300 N 30N 300 Nm 0.75 m 0.75m 0.75 m 0.75 m

A:

Q: A 0.5 kg mass is projected up a long 25° inclined plane with an initial speed of 4.5 m/sec. The…

A:

Q: Problem 10.8 - A beam is built up from two standard rolled-steel mỹímýmỹmm mỹmmmmjumm mmg…

A:

Q: A cantilever beam of span /carries a uniform distributed load of intensity wthroughout its span.…

A:

Q: What is the horizontal support reaction RAX at support A for the ?frame shown below

A: Summation of all the forces along horizontal direction is zero. Since, there is no horizontal force…

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.