The tank shown with elliptical cross-section is fabricated from 11.7 mm steel plate. Determine the maximum longitudinal stress caused by an internal pressure of 1.9 MPa. In the figure, let a = 741 mm and b =310 mm. pz 27/ Answer must be in MPa. Hint: Where a and b are the length of semi-major and semi-minor axes respectively. 1 Previous

The tank shown with elliptical cross-section is fabricated from 11.7 mm steel plate. Determine the maximum longitudinal stress caused by an internal pressure of 1.9 MPa. In the figure, let a = 741 mm and b =310 mm. pz 27/ Answer must be in MPa. Hint: Where a and b are the length of semi-major and semi-minor axes respectively. 1 Previous

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pin-connected structure shown in the figure consists of two cold-rolled steel (E = 30,000 ksi) bars (1) and a bronze (E = 15,000 ksi) bar (2) that are connected at pin D. All three bars have cross-sectional areas of 0.375 in². A load of P = 11 kips is applied to the structure at pin D. Using a = 3 ft and b 5 ft, calculate the downward displacement of pin D. A (1) a B D (2) P a (1) b
Prob 5. Calculate the maximum deflection dmax and the angle of deflection on the supports of a uniformly loaded simple beam loaded as shown. The maximum bending stress is o=60 MPa. The cross section of the beam is square with a length of 8 cm on each side. The beam is made of aluminum having modulus of elasticity E = 70 GPa. q = 2.0 kN/m L= 2.0 m
3. Please show your complete solution.
Help please!
Hydrostatic forces on inclined plane surface 6Q. A rectangular gate having a width of 4 ft is located in the sloping side of a tank as shown in the figure. The gate is hinged along its top edge and is held in position by the force P. Neglect the friction at the hinge and weight of the gate. Determine the required value of P. V Water Hinge Gate 60° 6 ft 10 ft
SHOW SOLUTION AND ILLUSTRATION
The pin-jointed frame in the figure below has members of cross-sectional area A=1200mm² and young modulus of elasticity of 200.5 GPa. If a vertical concentrated load of 1200KN (downward) and horizontal force of 800KN (to the right) are applied at Point D. Determine: a. The vertical displacement at D in mm. b. The horizontal displacement at D in mm. c. The stress of AD due to actual loads in kN. d. The stress of AB due to horizontal unit load. e. The stress of BD due to vertical unit load. 4m B 3m C 3m F E
2. A two-member truss structure is loaded as shown. Determine the horizontal and vertical components of the displacement of point A. CY dimensions in meters TAB 3 A 80KN 4:5 EAB 70 GPa ; EAC=70 GPa AAB=150mm²; AAC = 100mm²
6. Determine ax and ay in the figure for problem 5 if the pressure at A, B and C is the same. Ans. ax = 0, ay = -g
Question 5) The horizantal cantilever rigid beam AB has no mass and it is supported by an elastic rod at point C. The modulus of elasticity of the BC rod is E=200 GPa with cross-sectional area of 4=200 mm'. Calculate the magnitude of the distributed load q acting on the system so that the BC rod can be elongated by 2 mm. FEA 3m rigid B A 2m 1.5m
Determine the maximum axial force that each object can carry if the maximum stress of object 2 is 50 MPa and the stress of object 1 is half the stress of object 2. The cross-sectional area of object 1 is 300 mm? and object 2 is 700 mm². P1 P2
Problem 2: A solid circular shaft is acted upon by the torques as shown. If G= 12, 000 ksi determine: a. Rotation of wheel D with respect to A. b. Shear stress at point E Diameter of shaft: A-B = 2in C-D = 2in B-C = 4in T1=3 m in.kips T2=7 m in.kips Ta= 8.5 Tm in.kips T4= 4.5 m in.kips T1 T2