The tank shown is fabricated from steel plate. Determine the minimum thickness of the plate which may be used if the stress is limited to 40 MN/m² and the internal pressure is 1.5 MN/m². (Compute two possible thickness values) 400 mm 600 mm

Q: pipe is hung from a barge, is lowered, new sections a stem enables a good degre- an other laving…

A: height of the pipe, h = 2000 mrmin = 400 mdiameter of the pie, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: Find the applied force which produce stress of 22 N/mm2 on cross sectional area of 5.98 mm2

A: Given data : Stress σ=22 N/mm2 Cross sectional area A=5.98 mm2   Required : Applied force

Q: Deep sea pipelines are used to transport oil and gas across large distances, at depths greater than…

A: Height of the pipe, h = 2000 mrmin = 400 mDiameter of the pipe, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: Determine the stress components at point H. And show the stress state for this point on a volume…

A: Show the force and moments on cross section H.

Q: Determine stress produced by tensile force of 20 N applied on cross sectional area of 5 mm2

A: Given data: Tensile force (F) = 20 N Cross sectional area (A) = 5 mm2 Need to determine the stress…

Q: Find the value of stress Force=0.889 N Area 0.1 mm2

A: Given data : Force=F Area=A   Required: Stress

Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…

A: Given data: -  The pressure inside vessel is P = 150 psi. The length of the vessel is L ft. The…

Q: The maximum shear stress (in MPa) in the

A: Given;  A cylindrical tank of;  Inner radius,r=7 mm  Thickness=50 mm  Gauge pressure= 2 MPa…

Q: Question 12 A 7-ft diameter spherical tank is subjected to an internal pressure of 45 psf. If the…

A:

Q: Can you calculate the stress for the remaining point instead of point 1 only?

A: Given: To find: State of stress at remaining points

Q: the stresses at point A.

A: To find Stresses at point A

Q: Compute the maximum shear stress (r7maz) that this solid can have. Hint: Problem 3 Use the Mohr's…

A: For solution refer below images.

Q: A cylindrical tank holding oxygen at 3,470 kPa pressure has an outside diameter of 425 mm and a wall…

A:

Q: A steel pipe 1.5m in diameter is required to carry an internal pressure of 650kPa. If the allowable…

A:

Q: A spherical stainless-steel tank having an inner diameter ‘D’, is used to store natural gas at a…

A: given data D = 620 mm    P =25 MPa    Tensile stress =1000 MPa  Shear stress = 440 MPa  modulus of…

Q: material is 280 MPa. Using a safety factor of 1.5, determine the material thickness of the tank in…

A:

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A is…

A: Introduction: The tension is created by fighting the bursting effect of the imposed internal…

Q: A spherical pressure vessel 4 ft. in diameter with a wall thickness of 0.25 in is subjected to an…

A:

Q: 2m Z 1.5 kPa R T I'm

A:

Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: A 4-ft diameter spherical tank is subjected to an internal pressure of 34 psf. If the wall thickness…

A:

Q: Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the…

A:

Q: For the figure shown below. Calculate the increase in vertical stresses (Ac) at point A at depth of…

A:

Q: Compute the normal and shear stress on a plane which is 45° inclined from vertical axis of a…

A: Given data: -  The angle of the plane with vertical axis is θ = 45o. The axial stress on the box is…

Q: View Policies Current Attempt in Progress A typical stainless steel cylindrical vessel is shown. The…

A: Given data D = 48 in t = 0.75 in P = 1.1 ksi Find Hoop stress = ?

Q: solve, show all steps/solutions. include all asked for, no partial answer or ill dislike

A: Given that,The diameter of rod = d = 1 inchHence, radius of rod = r = 0.5 inchConsider following…

Q: The inner radius of the pressurized cylindrical tank is 1.25 m and the wall thickness is 15 mm. It…

A: We are given the following data: The inner radius of the cylinder, r=1.25 m Wall thickness of the…

Q: The pressure tank shown is fabricated from 1/8-in steel plate. Calculate the allowable internal…

A:

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

A:

Q: For a raft of size 98.4 x 39.36 ft, compute the stress at 65.6 ft depth below the center of the raft…

A: Stress is defined as the intensity of force acting over a unit area. Stress and the load intensity…

Q: The closed thin-walled tank has an inner radius of r and wall thickness t and contains a gas of…

A:

Q: The steel plate has the dimensions shown. Determine the maximum axial force P that can be applied so…

A: Given Maximum allowable stress = 21 ksi  r= 0.25 in d = 1 in t = 0.25 in w= 5 in D = 2.52 in To find…

Q: 4.0 kPa is used to carry a 3.5 m3of water has a height of 2.0 m and thickness of 5.0 mm. Determine…

A: given:V=3.5m3h=2mt=5mmP=114KPa

Q: 4. Determine the minimum thickness of the tank plating if the internal pressure is ODD: 1.3MPa EVEN:…

A:

Q: A building weighing 100,000 Ibs is placed on the L-shaped slab shown. The soil below the basement is…

A: We know that, x=A1x1-A2x2A1-A2 A1=80×60=4800 ft2x1=802=40'y1=602=30' A2=50×20=1000…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.