The tank shown in the accompanying figure is being filled by Pipes 1 and 2. If the water level is to remain constant, what is the mass-flow rate of water leaving the tank at Pipe 3? What is the average velocity of the water leaving the tank? Pipe 1: d = 1 in. V = 2 ft/s Pipe 2: d = 1.75 in. V = 1.5 fUs Pipe 3: d 1.5 in. V= ?

The tank shown in the accompanying figure is being filled by Pipes 1 and 2. If the water level is to remain constant, what is the mass-flow rate of water leaving the tank at Pipe 3? What is the average velocity of the water leaving the tank? Pipe 1: d = 1 in. V = 2 ft/s Pipe 2: d = 1.75 in. V = 1.5 fUs Pipe 3: d 1.5 in. V= ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1(c) Water flows horizontally through a nozzle into the atmosphere under certain conditions, as shown in Figure Q1(c). Calculate: (i) Volume flow rate of water flowing through the nozzle in m3/s and L/s, respectively. (ii) Mass flow rate of water. (iii) Exit velocity at the outlet of the nozzle.
question is in ımage
What is the velocity of the flow of water in leg B of the tee shown in the figure? A 4 m diameter V = 6 m/s 4 m/s с B 2 m diameter V = ?
Water flows through a pipe of diameter 0.30 m. What would be the velocity V for the conditions shown in the figure below? 0.3 m Dia 10.3 m لم Water 2 SG = 0.8
12 litre/s 4.5 litre/s 5. Water is flowing in a pipe system shown below. The diameters of all pipes are 150mm. Calculate the flow rate and the flow velocity in all pipes. 3.8 litre/s 4.3 litre/s 4.4 litre/s 2.3 1litre/s 3.3 litre/s M 4.2 litre/s 2.6 litre/s
reply A cylindrical tank containing water is 3m in diameter. It has an orifice 100mm in diameter punched in its bottom. If C=0.60, find the time in minutes for the head 8m to be reduced to 2m.
As shown in the figure below, water behind a dam enters an intake pipe at a pressure of 24 psia and velocity of 5 ft/s, flows through a hydraulic turbine-generator, and exits at a point z1 = 220ft below the intake at 19 psia, 45 ft/s, and a specific volume of 0.01602 ft³/lb. The diameter of the exit pipe is 5 ft and the local acceleration of gravity is 32.2 ft/s2. Water Dam P1 = 24 psia V = 5 f/s Generator i Turbine P2 = 19 psia 2 = 0.01602 ft³/b V2 = 45 ft/s -D2 =5 ft Water Evaluating the electricity generated at 8.5 cents per kW · h, determine the value of the power produced, in $/day, for operation at steady state and in the absence of internal irreversibilities. Value = $ i /day
Water flows through a pipe of diameter 0.30 m. What would be the velocity V for the conditions shown in the figure below? 0.3 m Dia 10.3 m >1 Water 2 SG = 0.8
The flow rate of water through a 10-cm-diameter pipe is to be determined by measuring the water velocity at several locations along a cross section. For the set of measurements given in the table, determine the flow rate.
Problem 4: Approximating Discharge from Velocity Consider steady flow in a stream d = 0.50 m deep and w = 3.0 m wide ("into the page"): Part A Part B h X X The velocity distribution is u = Umax(1- h²/d²), where Umax = 0.20 m/s. A few sample values are shown in the following table: 0.25 h[m] 0 u [m/s] 0.20 0.15 ▼ Part A On the figure, sketch the velocity profile using the equation. No need to calculate points. Part B On the figure, sketch an approximate velocity profile, with an upper area and a lower area. Plot the average velocity for the upper area and the lower area (hint, recall the wedding cake). Part C Using your approximation, calculate the discharge Q [m³/s]. Part D Using your approximation, calculate the average velocity V[m³/s].
I need the answer as soon as possible
Hello , can I get an answer please?