The system shown in Figure 4 consists of a point mass M 5 kg and a massless L-shaped lever. The lever has lengths a 0.5 m and b 0.75 m. The system is connected to two springs, each of stiffness ki = kz-1000 N/m, and a dashpot of damping coefficient e 50 kg/s. A torsional spring Kr - 250 Nm/rad is attached at the pinned point O. Point A at the end of spring kı is given a sinusoidal displacement of amplitude yo and frequency 5 Hz. Determine the magnitude y, required for mass M to have a steady state amplitude of 10 mm. Fixed end y() = y, sin(mt) K, I-frame slides smoothly along upper and lower surface. M Pinned point, O Fixed end Figure 4

The system shown in Figure 4 consists of a point mass M 5 kg and a massless L-shaped lever. The lever has lengths a 0.5 m and b 0.75 m. The system is connected to two springs, each of stiffness ki = kz-1000 N/m, and a dashpot of damping coefficient e 50 kg/s. A torsional spring Kr - 250 Nm/rad is attached at the pinned point O. Point A at the end of spring kı is given a sinusoidal displacement of amplitude yo and frequency 5 Hz. Determine the magnitude y, required for mass M to have a steady state amplitude of 10 mm. Fixed end y() = y, sin(mt) K, I-frame slides smoothly along upper and lower surface. M Pinned point, O Fixed end Figure 4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure 2 shows an electrical motor with mass M=13 kg located at the middle of pinned-pinned beam. A damper with damping coefficient of c=59 N.s/m is also attached to the beam at point A . Considering Young’s modulus of the beam E=98 GPa, moment of inertia of the beam I=18 mm4, length of the beam L=1 m, unbalance mass of m0 =1.9 kg, eccentricity e=2.8 mm, and zero initial conditions, find the steady state amplitude of point A at resonance in millimetre (mm).
Solve correctly please.
Please solve only 4,5
The figure below shows a single degree of freedom control surface/actuator system. The control surface has a mass moment of inertia J = 30 kg.m2 about the hinge, the effective actuator stiffness and damping values are k = 3000 N/m and c = 500 Ns/m respectively and the rotation of the control surface is rad. The actuator lever arm has length a = 0.2 m. A force f (t) = 58 (t) N is applied to the control surface at a distance d = 1 m from the hinge. It is assumed that the main surface of the wing is fixed rigidly as shown in the figure. Assume small angle approximation. Determine the tip velocity (velocity at the location of f(t)) at t = 0.1 s 0(t) f(t) C 152.74 mm/s 499.47 mm/s 583.77 mm/s 400.63 mm/s 285.64 mm/s d
A vehicle weighing 5,000 lb is supported on four identical springs and four identical viscous dampers. The static deflection of the vehicle under its own weight is 10 in. Determine the damping required for each of the dampers so that the critical damping is achieved.
spring is to be inserted with an initial compression to produce a force equal to 125 N between the right-hand end of the lever and the stop. When the maximum force at A reaches to a value of 200 N, the end of the lever moves downward by 25 mm. assuming a spring index 8 determine the following parameters: 1. Spring rate 2. Size of the wire 3. Outside diameter of the spring 4. Number of active coils, and 5. Free length, assuming squared and ground ends Note: the allowable shear stress may be taken as 420 MPa, and G = 80 GPa. Hint: Ans. 0.33 N/mm: 3.4 mm; 27.2 mm; 77 mm - 200 mm - 200 mm Lever Stop -Spring
1. A system is needed to be designed as damped spring mass system. Calculate the amplitude of vibration. Stiffness=10 kN/m; mass 2Mg; and dashpot coefficient 2 kNs/m. It is subjected to a harmonic force = 500N @ frequency 0.5Hz ANS. X₁-43mm 2. What is the A length of three springs connected in series and parallel? Change in length of the spring is 4 cm. reelle k₁ llll пише m=160 gram
Pravinbhai
Question 1: Determine the flexibility influence coefficients of the mass-spring system shown in Figure 1 m3 m2 m1 k1 k2 k3 Figure 1
QUESTIION A. B AND C
A metal polishing machine consists of a box full of ceramic particles mounted on the top of a shaker device as shown in the figure below. The shaker runs at f = 24.2078 Hz and carries an out of balance mass of mo = 19.9725 kg at a distance of e = 0.0499 m from the centre. The static deflection of the spring is A = 19.3179 mm, the damping constant is c= 20239.4652 kg/s and the total mass of the machine is M = 813.8726 kg. Assume that gravitational acceleration is g = 9.81 m/s?. The amplitude of the steady state response of the system is:
for the system shown in Fig. (2) the values m = 1,750 kg, c = 3,500 N-s/m, k = 7x 105N/m, a = 1.25 m and b = 2.5 m. 1. Draw F.B.D. 2. find equation of motion & wd. 3. 4. Determine the value of the critical damping. Calculate time response. k rigid link m