The system in the figure is in equilibrium: a) Make 4 free body diagrams b) Calculate Ta(N) and the weight Q Ta WWW. www.chan TB JB. TB 15 N d=53⁰ B = 37° در

Q: A single degree of freedom system (SDOF) of mass m and stiffness k is found to vibrate with a period…

A:

Q: Q2: Determine completely the resultant R of the three forces shown in the figure below. 60 kN 100 kN…

A: Given that:

Q: a. If a concentrated load of 10O0kg can be placed only at any of the 1-meter interval points on the…

A:

Q: Particle A lies on the x-y plane and is acted on by the three forces shown. Find the resultant of…

A:

Q: Problem 3 Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on…

A: The FBD of the beam is shown below:

Q: A B k 5.0€ 15.0 10.0 Colculor displacement in B

A: Given data:

Q: The uniform rod (diam = 5 cm., Length = 10 m.) shown in the figure is attached to a hinge at A. It…

A:

Q: 15 t 30 t 6 t/m 3 m 2 m 2 m 3 m 40 000 сm" B 120 000 сm" 80 000 сm" 6 m

A: Draw FBD: Resolving all horizontal forces:

Q: Determine the total displacement of joint D.

A:

Q: Problem 3.2 The members of a truss are pin connected at joint O. (Figure 1) Figure 1 5 kN 7 kN of 1…

A: Required : Magnitude of F1 for equilibrium. The  angle θ for equilibrium.

Q: Q.10 The diameter of a solid shaft is D. The inside and outside diameters of a hollow shaft of same…

A: given-dia of the solid shaft=D

Q: If d = 1 m, and 6 = 30°, determine the normal reaction at the smooth support A if P = 400 N. Neglect…

A: Given :

Q: Part G A proton with mass m moves in one dimension. The potential-energy function is U (x)=a/22-8/2,…

A:

Q: If the density of the solid shown is 5 slug/ft3, determine the mass moment of inertia about the y…

A: The density of the solid is 5 slug/ft3. Consider the figure.

Q: 4. Which among the following is the correct format for Rayleigh's method?

A: Introduction: Rayleigh's method: This is the method of dimension analysis. This is a very popular…

Q: 5. Determine the v-component of F1. (N) 6. Determine the u-component of F1. (N)

A:

Q: Required information Consider the following figure. 10 in.- AO E © P F O BO 4 in. lb lb ↑ D T 5 in.…

A: Given: To find: The components of the reactions at A: Ax =  Ay =  The components of the reactions…

Q: 13. Dynamics of rigid bodies is a branch of strength of materials. O True O False 14. Hydrostatic…

A:

Q: 2 m 1m- 2 m D. wwwwe 1.5m www k 100 N/m = 100 N/m www www

A:

Q: The table below shows the free-body diagrams of the forces acting on 4 different rigid bodies. Since…

A: A free body diagram is indeed a pictorial depiction of a single structure or a network of entities…

Q: 9. If the time rate of growth of a population is directly proportional to the size of the…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: 5.13 Let a material contiuum have the constitutive equation O = ad,Du + 2BD, where a and Bare…

A: When a liquid-moves through a pipe, or a solid item moves via a fluid, it tends to be at the same…

Q: In the figure, the forces acting on the concrete dam body are hydrostatic pressure, underbody…

A: Take the unit inside width of the dam.The thrust force due to ice, Pbuz = 150kNThe density of…

Q: Part A Determine the moment produced by force FB about point O (Figure 1). Express the result as a…

A: Given :

Q: Determine the force P required to start the wedge shown in the figure. The angle of friction for all…

A:

Q: The mass of a block m = 4.59 kg has part of its volume submerged in a beaker of water. The block is…

A:

Q: A solid conical bar of circular cross-section is suspended vertically as shown in the figure. The…

A:

Q: The crate shown is held against wedge B by a spring. The spring is 96.0% of its original…

A:

Q: Determine the value of P so that its vertical displacement is limited to 2.00 mm. 2.0 m 3.0 m 2.0 m…

A:

Q: for Figure, use the interaction diagrams to determine P, for the short column shown. fy = 420 Pa and…

A:

Q: Knowing that the lengths X, Y and Z in the figure below are 3 m, 5 m and 4 m, respectively. The…

A:

Q: Use the column interaction diagrams to determine (P.) value for the short column shown in Figure, if…

A: In order to determine the Pn value based on the given data we need to find Kn value from interaction…

Q: Develop a finite element model to solve the displacement at the point where the 10000 N is applied…

A:

Q: Solve for the unknown variable in the equation (x+2)/3 - (x+2) = 3(x-2) + ((x+5)/6) * O x=2 О х-1 O…

A:

Q: A city has a population of 10,000 with an area of rapid filter as 20 m² and an average filtration…

A: Given data: Population of city = 10,000 Area pf rapid filter = 20 m2 Average filtration rate = 4000…

Q: A weight of 900N is supported by two metallic ropes as shown in the fig. The tension in OB rope is…

A: Given: Forces in members To find: Tension in the rope OB

Q: F = 882 N 40° 60

A:

Q: As shown in Figure 7, a mouse can use the mechanical advantage provided by a hydraulic machine to…

A: Concept: We have to draw reference of Pascal's Law in fluid mechanics. Using the concept of pascal…

Q: Determine the z-coordinate of the mass center of the homogeneous paraboloid of revolution shown.…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.