The system in the figure below is in equilibrium. A 45.0-kg beam that is hinged on the floor is also held at rest by the cable. A hanging mass of 225 kg is placed at the end of the beam. Calculate: 225 kg a) The tension in the cable; and b) The reaction forces exerted on the beam by the hinge. 30° 45°

The system in the figure below is in equilibrium. A 45.0-kg beam that is hinged on the floor is also held at rest by the cable. A hanging mass of 225 kg is placed at the end of the beam. Calculate: 225 kg a) The tension in the cable; and b) The reaction forces exerted on the beam by the hinge. 30° 45°

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A 400.0-N sign hangs from the end of a uniform strut. The strut is 4.0 m long and weighs 600.0 N. The strut is supported by a hinge at the wall and by a cable whose other end is tied to the wall at a point 3.0 m above the left end of the strut. (a) What is the y component of the tension in the rope? (b) What is the x component of the tension in the rope? (c) What is the magnitude of the tension in the rope? (a) y component of the tension: Ty = (b) x component of the tension: Tx = (c) What is the magnitude of the tension in the rope?
In the figure below, a uniform beam of weight 420 N and length 2.8 m is suspended horizontally. On the left it is hinged to a wall; on the right is it supported by a cable bolted to the wall at distance D above the beam. The least tension that will snap the cable is 1200 N. Cable Beam (a) What value of D corresponds to that tension? (b) Give any value for D that won't snap the cable. m
As shown below, a sign weighing 314 N is hanging (via a wire) from a uniform 344 N beam of length L. Additionally, the beam is attached to a cable that makes an angle 0 (0 = 41°) with the beam. 0.3 L 0.7 L A 6 D 0 Determine the tension in the cable and the magnitude & direction of the force the hinge (the orange circle) exerts on the beam. Cable tension = Hinge force = Direction of hinge force = -- Choose quadrant -- ŷ o relative to the horizontal in quadrant
A uniform beam has a length of 15.2 m and a mass of 37.3 kg. The beam is horizontal and resting (in equilibrium) on two supports. One of the supports is located 4.09m to the right of the beam's center of mass. The second support is located 1.96 m to the left of the beam's center of mass. How much upward force is exerted on the beam by the first support?
A uniform drawbridge must be held at a 38o angle above the horizontal to allow ships to pass underneath. The drawbridge weights 55000 N and is 15.0 m long. A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place. What is the tension in the cable? Find the magnitude and direction of the force the hinge exerts on the bridge. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks? What is the angular speed of the drawbridge as it becomes horizontal? What is the velocity of the drawbridge, just before it “hits” (i.e. goes horizontal)?
A horizontal 4.0 m long 5.0 N uniform bar at one end is attached to a wall by a frictionless hinge; and at the middle of the bar there is a vertical cable pulling down 7.0 N, and at the middle of the bar there is also a cable that is at 45 ° to the horizontal pulling up as shown. ii) What is the magnitude of the horizontal component of the force on the bar due to the hinge?
A horizontal 12.5 kg beam 2.2 m long is attached to the wall by a hinge at its left end. A cable is connected from the right end of the beam to the wall, at an angle of 26 ° above the beam, as shown below. A 60 kg sign is hung 1.7 m from the left end of the beam. Part A Find the tension in the cable. Part B Find the horizontal force exerted on the wall by the hinge. Part C Find the vertical force exerted on the wall by the hinge
In the figure, one end of a uniform beam of weight 280 N is hinged to a wall; the other end is supported by a wire that makes angles θ = 28° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam.
A uniform 34.0-kg beam of length { = 5.95 m is supported by a vertical rope located d = 1.20 m from its left end as in the figure below. The right end of the beam is supported by a vertical column. (a) Find the tension in the rope. (b) Find the force that the column exerts on the right end of the beam. (Enter the magnitude.)
In the figure, one end of a uniform beam of weight 100 N is hinged to a wall; the other end is supported by a wire that makes angles 8- 29 with both wall and beam. Find (a) the tension in the wire and the (b) horizontal anid (c) vertical components of the force of the hinge on the beam. Hinge (a) Number Units Units (b) Number Units (c) Nurmiber
A uniform beam 4.2 m long and weighing 2200 N carries a 3700 N weight 1.50 m from the far end, as shown in the figure below. It is supported horizontally by a hinge at the wall and a metal wire at the far end. 1) How strong does the wire have to be? That is, what is the minimum tension it must be able to support without breaking? Express your answer in newtons. 2) What are the horizontal component of the force that the hinge exerts on the beam? Express your answer in newtons. 3) What are the vertical component of the force that the hinge exerts on the beam? Express your answer in newtons.
A uniform 22 kg beam, 3.0 m long, is attached to a wall on the left by a hinge, and is supported by a cable on its right end. A 13 kg monkey hangs from the beam, 1.0 m from the left end. a) Determine the tension in the cable. b) Determine the magnitude of the force due to the hinge on the beam.