The system given in following figure, is an example for

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: Q17-In problem Q16 determine the percent elongation. (b) If the specimen necked to an area = 92mm2,…

A:

Q: -139/A 3-m-high, 6-m-wide rectangular gate is hinged at he top edge at A and is restrained by a…

A:

Q: 2. The circular shaft has fixed supports at both ends, points A and D. Determine the torque that…

A:

Q: d. none of the above. 79. The relation [AV]1/vi evaluated at the inlet with respect to [AV]2/v2…

A: P1=14.7psi T1=80 F Q=1000cfm P2=100psi T2=400 F

Q: の5 の25 23

A: Representation of three-dimensional object in two dimensional is known as an orthographic…

Q: Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The…

A: Given:- P=3.5kW m=2mm Pressure angle=20° N=1800rpm To find:- g) Torque on gear 4

Q: 1. The tower is held in place by three cables. If the force of each cable acting on the tower is…

A:

Q: 400N 200 Z00 N さ

A: Given Data :

Q: Determine the reactions in C and D, the shear force diagram and the bend moment diagram of the…

A: Consider upward force & CW moment as (+)ve and downward force & CCW moment as (-)ve. Let…

Q: Determine the unit vector of r.

A:

Q: Questions 6-8 relate to the structure shown in Figure 2. A beam shown in Figure 2 is constructed…

A: In the above problem we need to calculate the area moment of inertia of the given cross section .So…

Q: Problem III. A cable was used to dry the clothes from wet laundry by hanging as shown below. The…

A:

Q: A rigid, well-insulated tank contains a two-phase mixture of ammonia with 0.0025 ft of saturated…

A: The given information in the problem is listed in the following attached image:

Q: 4. Wet concrete exerts a pressure distribution along the wall of the form. Determine the resultant…

A:

Q: Die Ntef d CW ad d 107 30T 167 327

A:

Q: Questions 56-60 are based on the information given here. Air, as an ideal gas, undergoes a…

A:

Q: PROBLEM 1: Estimate the kilowatt pump you would need to pump 450 Liter/min of liquid water at 20°C…

A:

Q: 8. 000 *性 10 20 G- 020 10 74 100 140 Rajah L8

A:

Q: 3/X15 In the design of a conveyor-belt system, small metal blocks are discharged with a velocity of…

A: Given: Initial speed of the block→V1=0.40 m/s Final speed of the block→V2=0.14 m/s Coefficient of…

Q: Determine the x-coordinate of the mass center of the homogeneous hemisphere with the smaller hemi-…

A:

Q: y F1 = 30 N 3 4 F3 = 50 N 20° F2 = 20 N

A: From the data given in question, F1 = 30 N F2 = 20 N F3 = 50 N

Q: 18 40 40 72 13

A: orthographic view : theses are the projection view when viewed by a observer from side view , top…

Q: A disk of mass, m, and radius, R as shown in the figure is being supported by an elastic shaft with…

A:

Q: THE SYSTEM SHOWN BELOW IS IN EQUILIBRIUM IF THE WEIGHT OF B IS 48 NEWTON CALCULATE THE WEIGHT OF A,…

A:

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: Determine the internal forces acting in members, HC, JD, and KE. State if the members are in tension…

A: Drawing the free body diagram of the system as shown below,…

Q: D 3.2-5. Use the graphical method to demonstrate that the fol- lowing model has no feasible…

A:

Q: 3-50/Consider the system shown in Fig. P3-50. If a change of 0.7 kPa in the pressure of air causes…

A: Given Specific gravity of mercury SGhg=13.56 and Specific gravity of brine SGbr=1.1 Write the static…

Q: Trace the curve of y²=x²+5x+7

A: Determine values of Y by substituting different values of x

Q: 3-15. The rigid pipe is supported by a pin at A and an A-36 guy wire BD. If the wire has a diameter…

A:

Q: The components of an electronic system are located in a 1.8-m-long horizontal duct whose cross…

A: Given:- k=0.02717W/m.k Ts=65Tf=30 To find:- Total power rating of the electronic devices that can be…

Q: 9. An R-L series circuit contains a resistor and an inductor. The resistor has a value of 6.5 2. The…

A: Question - 10: The voltage drop across the resistor in an R-L series circuit can be found using…

Q: 3-61E A long, solid cylinder of radius 2 ft hinged at point A is used as an automatic gate, as shown…

A:

Q: A 1000 kg automobile accelerates from 10 km/hr to 120 km/hr. How much work does this require?

A: Question(4)Given:Mass  Initial Velocity Final Velocity To find:The required Work

Q: (4) 8.8.8.8 16 8 8 16 21

A: the question is not fully asked   bricks and blocks are given

Q: Determine the x-coordinate of the mass center of the homogeneous hemisphere with the smaller hemi-…

A:

Q: Find the y component of the F1 = 256. Use whole value for your final answer. Numerical value only.

A:

Q: 3-49 The pressure difference between an oil pipe and water pipe is measured by a double-fluid…

A: Density of water =1000 kg/m3 Density of mercury = 13500 kg/m3 Density of Glycerine = 1260 kg/m3…

Q: 15 30 10 50 30 30 25

A:

Q: 5-95 Air flows through a pipe at a rate of 200 L/s. The pipe consists of two sections of diameters…

A: Given data: Flow rate of air = Q = 200 L/s = 0.2 m3/s Diameter of section 1 = 20 cm = 0.2 m Diameter…

Q: The pipe assembly supports the vertical loads shown. Determine Equations of Equilibrium: the…

A: Fro the given  Free body diagram(FBD) F1 =6 kN and F2=4 kN  Now by considering A as origin the…

Q: A plate was subjected to a tensile force P=100 KN as shown on the figure. If the allowable stress is…

A:

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.