ZVY @Deep poursWet burlapThe suitable method of curing for columnisPonding and immersionPlastic sheetAll of theseTrue- ١٠:٥٣ صdocs.google.comFalseDegree of hydration decreases with curingSegregationUsing vibrator with long period increaseWorkabilityAsiacell.***

As multiple questions are asked and as per the guidelines only very first question will be answered.…

The suitable method of curing for column is Ponding and immersion Wet burlap Plastic sheet O All of these * Degree of hydration decreases with curing * True False Using vibrator with long period increase * * Segregation O Workability

The suitable method of curing for column is Ponding and immersion Wet burlap Plastic sheet O All of these * Degree of hydration decreases with curing * True False Using vibrator with long period increase * * Segregation O Workability

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

N=2
(a) Discuss the importance of these products in the hydration process: i) C-S-H gel ii) Ca(OH)2 (b) Approximately 70% of concrete is made up from aggregates. Some stated that aggregates are only an inert material in concrete and have negligible effects on concrete. Based on your understanding, discuss whether you agree or disagree the above statement with justifications. (c) Explain why concreting works in the rain is prohibited during construction. Give two (2) consequences resulting from this practice from the point of view of excessive water in concrete mix.
Construction material
PV laundry facility uses 1 m/min and wants to design an exchange process to remove hardness from the water. The municipal water that they use contains 80 mg/L of calcium and 36.6 mg/L of Magnesium. Total hardness should be reduced to 80 mg/L of CaCO3. The resin has a Total Hardness (TH) capacity of 60 kg TH/m³ of resin, and the recommended hydraulic loading rate is 0.5 m³/m².min. a) What is the water flow rate (m³/d) that needs to be treated? b) What is the total daily resin volume (m³) required to soften the water? c) What is the area of the exchanger needed?
Q1) Read the following sentences, write true or false, and correct the sentences that are false:- 1-Iraqi specification No. 5 limited max SO3 in Portland cement by 1.5% when C4AF 8%. 2-The actual value of the heat of hydration depends on water cement ratio. X X 3- The alkali silica reaction is very fast, happen between active silica in the cement and the alkalis in aggregate. 4- Sulphate in mixing water should not be more than 10,000 ppm. ✓ 5- Higher curing temperature decrease earlier strength, but it increases 28-day strength of concrete. Call vings: [SMI
I need the answer as soon as possible
Evalaution sof aggregates Sources.
In a concrete mix having 0.5 m³, solid volume is 550 kg. Weight of water is 40% of total solid volume. If specific gravity of solids is 2.40. Air content in the mix(in percentage) will be-
Answer by true or false for the following: 6- The presence of an excessive proportion of one particle-size in an aggregate grading may cause harshness. * a-True b-False 7- Pan-type mixers are particularly good for mixing rich and dry mixes. * a-True b-False 8- Prolonged mixing increases the air content of the mix. * a-True b-False 9- Concretes with the larger-sized aggregates require less mortar per unit volume of concrete * a-True b-False 10- Workability increases with the decrease in the size of the aggregate. * a-True b-False 11- The strength determined in the splitting tensile test is higher than that of the direct tensile test. * a-True b-False…
One common issue with air strippers is scaling due to hardness in the water. Please design an excess lime pre-treatment step to remove the water hardness (determine the softening chemical addition rates [mass/hour] of Ca(OH)2 and Na2CO3) if the water chemistry is as follows [CO2] = 5 mg/l, [Ca2+] = 50 mg/L, [Mg2+] = 6.1 mg/L, [Na+] = 23 mg/L, [Alkalinity] = 150 mg/L and [SO42-] = 24 mg/L
8 - Which of the following properties is the difference that distinguishes Silica fume from other pozzolan? I. Increases late strengths. II. It increases early strengths. III. It increases the need for water. IV. It increases the temperature of hydration. V. Decreases the heat of hydration. A) I, II, and VB) I and VC) Solo IIID) II, III and IVE) I, II, III
Standard Test Method for Ductility of Bituminous Materials 4) what is the distance between clips of ductility mould ?5) What is the length of the briquttemould ?6) What is the effect of pouring temperature ?