The stress-strain diagram for a steel alloy having an original diameter of0.5 in. and a gauge length of 2 in. is given in the figure. Deterinine approx-imately:(a) the Modulus of Elasticity for the material(b) the load on the specimen that will canse yielding(c) the ultimate load the specimen will support(d) the Modulus of Resilience(e) the Modulus of ToughnessNote that the lower scale supports the lower curve and the upper scalesupports the upper curve. The lower eurve is the initial portion of the entirestress-strain curve that is picked up by the upper curve. The two eurvestogether represent one complete stress-strain curve. For part (e) you canapproximate the area under the curvescounting boxes.o (ksi)8070 -60-504030 -20100.E ()Iower scaleF0.28- 0.0035- 0.24– 0.0030-0.20- 0.0025-0.16- 0.0020- 0.12- 0.0015-0.08- 0.0010-0.04-0.0005

As per BARTLEBY rule i answer only one question and first 3 subparts, so answered only fist 3 parts…

The stress-strain diagram for a steel alloy having an original diameter of 0.5 in. and a gauge length of 2 in. is given in the figure. Deterinine approx- imately: (a) the Modulus of Elasticity for the material (b) the load on the specimen that will canse yielding (c) the ultimmate load the specimen will support

The stress-strain diagram for a steel alloy having an original diameter of 0.5 in. and a gauge length of 2 in. is given in the figure. Deterinine approx- imately: (a) the Modulus of Elasticity for the material (b) the load on the specimen that will canse yielding (c) the ultimmate load the specimen will support

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 8 mm & Modulus of Elasticity 201 GPa. It is found that the specimen has undergone an extension of 1.6 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain-induced due to the load "F" on the specimen is 4.1 x 10-3. Solution Cross-sectional Area, A (in mm²) Tensile Load, F (in N) Length of the Specimen (in mm)
Sketch two more stress-strain diagrams, again one for a ductile material and one for a brittle material. Draw the stress-strain diagrams so that the modulus of toughness for the brittle material is greater than the modulus of toughness for the ductile material.
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 5 mm & Modulus of Elasticity 207 GPa. It is found that the specimen has undergone an extension of 1.2 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain-induced due to the load "F" on the specimen is 3 x 10-³. Solution Cross-sectional Area, A (in mm²) = Tensile Stress, (in N/mm²) = Tensile Load, (in N) = Length of the Specimen (in mm)
A solid steel bar 250 mm long is 10 mm square over part of its length, the remainder being circular with a diameter of 25 mm. A gradually applied tensile load P kN induces maximum stress in the bar of 200 MPa. The total strain energy in the bar when this stress of 200 MPa is acting is 1,3 Joule. Take E = 200 GPa Calculate : The load The length of the square portion of the bar The load that falls from a height of 8 mm and induces 1,3 Joules in the bar
A horizontal bar, fixed at one end (x = 0), has a length of 1 m. and cross-sectional area of 100 mm2 Its elastic modulus varies along its length as given by E(x) = 100e-x GPa, where is the length coordinate (in m) along the axis of the bar. An axial tensile load of 10 KN is applied at the free end (x = 1). The axial displacement of the free end is..... mm
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 9 mm & Modulus of Elasticity 205 GPa. It is found that the specimen has undergone an extension of 1.7 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain-induced due to the load "F" on the specimen is 3.7 x 10-3. Solution Cross-sectional Area, A (in mm2) Tensile Load, F (in N) Length of the Specimen (in mm)
100 mm must elongate only 5 mm when a tensle load of 100,000 N is applied. Under these A cylindrical specimen of a brass alloy having a circumstances what must be the radius of the specimen? Consider this brass alloy to have the stress-strain behavior shown in Figure below. Tensile strengh 450 MPa (65,000 p A00 10 pu 300 200- 30 Yield strength 250 MPa (36,000 psi 2아 100 1아 100 0.005 0.20 0.30 0.40
An element of material in plain strain is subjected to strains epsilon_x=0.0015, epsilon_y=-0.0002, and gama_xy=0.0003. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
200 stress 150 (MPa) 100 50 0.1 0-2 strain From the tensile stress-strain behavior for the brass specimen the diameter is 12-8 mm Calcalate the folluwing:- %3B 1- The Yield stress. 2-Modulus of elasticity. 3 - The Tensile strength.
Consider a cylindrical specimen of a steel alloy with 8.5 mm diameter and 80 mm long that is pulled in tension. Estimate these mechanical properties using the figure: Modulus of Elasticity in MPa and psi Modulus of Resilience in MPa and psi