The strength per meter of the longitudinal joint is 500 kN, whereas for the girth joint it is 220 kN. What is the maximum diameter of the cylinder tank if the internal pressure is 2.0 MPa? d.455 mm c.445 mm b.440 mm a.450 mm

The strength per meter of the longitudinal joint is 500 kN, whereas for the girth joint it is 220 kN. What is the maximum diameter of the cylinder tank if the internal pressure is 2.0 MPa? d.455 mm c.445 mm b.440 mm a.450 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The steel cylinder has a specific weight of 490 l6/ft" and acts as a plug for the 1 ft long slot in…

Q: The steel cylinder has a specific weight of 490 lb/ft° and acts as a plug for the 1 ft long slot in…

A: The given data is; ρcylinder=490 lb/ft3ρwater=62.4 lb/ft3Radius, R=0.35 ftAB=0.5 ftθ=2Sin-10.250.35…

Q: Air Manometer fluid SG = 2.67. Oil SG = 0.87 P2 AGURE P3-134

A: Solution:- We know that the pressure difference in manometer between two point at same label pA-pB…

Q: The closed tank contains oil (SG=0,8) ,water and air with the air pressure (gage) of po = 500 Pa at…

A: Draw pressure diagram as shownP1=500pap2=0.8×9810×0.82=3139.2pap3=9810×0.82=3924pa

Q: The 5 ft diameter cylinder weighs 5000 lbs. and is 5 ft long as shown.compute the vertical reaction…

A: Diameter of cylinder (d) = 5 ft Length of cylinder (L) = 5 ft Weight of cylinder (W) = 5000 lb…

Q: a sump to an overhead reservoir. The static lift is 40 m out of which 3 m is the suction lift. The…

Q: 3-91 The weight of the gate separating the two fluids is such that the system shown in Fig. P3-91 is…

A: Given: F1/F2 = 1.70 SG¹ = 0.86, SG² = 1.25 Required: h/H

Q: -Air 45° Water dz -Mercury d2 7) Find the difference in pressure between tanks A and B if d, = 1 ft,…

A: Given data, d1= 1ft, d2=6in = 0.5ft d3= 1.5ft d4 = 8in= 0.67ft

Q: The piston rod of an air operated press is to exert a maximum force of 20 kN. During the application…

A: Given, Maximum force = 20 KN. Air pressure = 700 kPa. Piston rod length l= 760mm.One end pinned…

Q: Q.4 Springs A close-cooled helical spring is to carry a load of 150 N. The mean coil diameter has to…

A: Given data- A close-coiled helical spring- Load W=150 N, Mean coil diameter = 10 times of the wire…

Q: Determine support reaction

A: Introduction : The given beam is simply supported beam . The beam is loaded with uniformly…

Q: In fi. If h1= 1 m, h2=. 0.5 m. what is the pressure at. A ?(. SG1= 0.7, S.G2= 0.8) s.g.1 h2

Q: spherical pressure vessel designed using steel has diameter of 36inches, shell thickness of 3/16…

Q: F 25 mm 400 mm 10 kN 75 mm Ø 25 mm 0 oil Hinge bo000000000

Q: Q1. In a piston-cylinder assembly attached with spring load is filled with 60 kg of water at…

A: Given Data - m = 60 kgPi = 250 kpaTi = 25 °C = 298 KA = 0.1 m2 v2 = 0.2 m2k = 100 kN/mx = 20 cm

Q: 24 KN / m B 12 m 200 KN 6 m A D 10 m

Q: Q6-Determine the maximum force P that can be applied without causing movement of the 90-kg crate…

Q: 2) How large are the reaction forces and bar forces in the given jib? Given: F1 = 20 kN, F2 = 10 kN,…

Q: assuming smooth contact surfaces, determine the reactions A,B,C and D on the cylinders as shown in…

A: Consider the reaction force at D is RD and the reaction force at C is RC. Similarly, the reaction…

Q: The hydraulic jack in the figure below is filled with oil at 56 lb/ft3. Neglecting the weight of the…

A: Hydraulic jacks are used to lift heavy loads by applying force from the hydraulic cylinder and also…

Q: Q2:- A steel cylinder of (s.g = 0.64) floats on water, submergence, h? find the depth of 4cm Water…

Q: e strength per meter of the longitudinal joint in the figure is 485 kN, whereas for the girth joint…

A: Given:Strength per meter of the Girth joint=200 kNStrength per meter of the longitudinal joint=485…

Q: Derive a formula for the pressure difference Pa - P in terms of the system parameters in the figure…

Q: 8.8 The spherical gas tank is made of steel (E = 29 × 106 psi, v = 0.3). The inner radius of the…

A: Data is as given

Q: Ex A bar ans: A13 X= 2-2 M The Smooth hari Zantel position planes in Find the distance X, as 1 kW…

A: Bar AB resting on two horizontal planes

Q: The piston at A has a cross-sectional area of 600 cm² while that of B is 100 cm². The difference in…

Q: A beam has a width of 200mm and a height of 250mm and is loaded as shown. Solve the moment of…

A: Given data in question UDL 6kN/m Span 10 m Point load 28 kN Width 200 mm Height 250 mm To find out…

Q: A load P=5 KN is supported by two concentric springs arranged as shown in figure below. The inner…

A: Load supported by two concentric springs = 5 kNNumber of turns in inner spring, n1 = 30…

Q: Determine the resultant force Por the Rorca system shown below. 201bA 10016 80 1b in

Q: The triangular valve (AB) which weighs 1500 Newtons closed at point A and is free at point B. What…

A: Length of the gate t=2sin50o=2.6108 m Depth of center of gravity from surface of water…

Q: inimum thickness o o 40 MN/m² and th mm -600r Figures P-1

A: Solution Given That Limited Stress σ=40 MN/m2 Internal Pressure P=1.5 MN/m2

Q: E Oil (0.80) D f B A

A: A we have to determine the reaction at B

Q: -80mm ↓P=240KN 0.6m P E=70 GP₂ ✓=0.3 800 KN 2 - A circular tube is loaded in compression, as shown…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

The strength per meter of the longitudinal joint is 500 kN, whereas for the girth joint it is 220 kN. What is the maximum diameter of the cylinder tank if the internal pressure is 2.0 MPa?

d.455 mm

c.445 mm

b.440 mm

a.450 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The tank shown is fabricated using a steel plate 1/6 of an inch thick. Determine the maximum tangential and longitudinal stresses developed caused by an internal pressure of 130 psi.
Within few minutes
From the figure below, determine reaction Ch.
Solve asap
Dont round off initial values, round off in final ans only plz ty
Current Attempt in Progress A 1-m-diameter cylindrical mass, M, is connected to a 2-m wide rectangular gate as shown in the figure. The gate is to open when the water level, h, drops below 2.5 m. Determine the required value for M. Neglect friction at the gate hinge and the pulley. 4 m h Water 1'm kg -1-m- diameter
water 3cm D=5 cm Mereury The tank in the has a 5 cm diameter plug at the bottom.on the rrght. All fluids are at zóc The Plag will pup out if the hydrestatic force is 30 for this condition what will be the readineg h ont Meicury mahometer on the left side2
For the tank shown in the figure, compute the pressure at points A & B. AIR 2m ail 2m water s.0.82 3m 4m Meraury s- 3.G
Please answer the following question in the picture make sure to draw a free-body diagram and show every step you make, THANK YOU SO MUCH FOR YOUR HELP!
3. Two coaxial cylinders 250 mr high have a liquid in between them, the outer cylinder had internal diameter 100 mm and the internal cylinder has external diameter 97.5 mm. Find the viscosity of liquid which produces a torque of 1 Nm upon the inner cylinder when outer one rotates at 90 rpm.
The 5 ft diameter cylinder weighs 5000 lbs. and is 5 ft long as shown. Compute the vertical reaction at B
For ACB beam with elasticity module E and inertia I;a) Find the elastic curve equation by singularity method?b) Find the reaction forces at point A?c) Find the reaction force at point B?