The stream function for a steady flow is given as For the coordinates (1,2) The x velocity component (u) is m/s (0.35;0.36:0.38;0.40:0.42) The y velocity component (v) is m/s (0.17,0.18:0.19,0.20:0.21) Linear strain rate in x direction is 1/s (0.15;0.16,0.17:0.18,0.19)
Q: Gommu has a pole that is made out of 2 parts. An iron and steel section. The iron section is 40cm…
A:
Q: Given that, bz (400mm x 3000)mm b3(400mmx yootim) Area 100000mm? %3D 400 XB00 01200000 mm2 Ab3 =…
A: Write the relationship between stress and area. For constant force F, the stress σ is inversely…
Q: Compute the decrease in volume of 2.5 x 10-4 m³, of mercury when subjected to a pressure of 20 x 105…
A: Given data: mercury's volume V=2.5×10-4 m3 Pressure P=20×105 N/m2 bulk modulus β=2.8×1010N/m2
Q: 12mm dia 18mm dia. P=12 kN 2 m. 12mm dial 2. Three steel cable jointly support a load of 12kN. The…
A:
Q: What will be the density of sea water at a depth of 1 km, if the density at the surface is 1025…
A: Correct option : (d) 1029.387 kg/m3
Q: A copper (shear modulus 4.2 x 1010 N/m²) cube, 0.442 m on a side, is subjected to two shearing…
A:
Q: The velocity distribution for the flow of oil (SAE 10W) at 38°C between two walls is given by V =…
A: V=100y0.1-y Shear stress is a type of stress that arises when a force is applied parallel to a…
Q: A stainless steel tube with an outside diameter of 46 mm and a wall thickness of 5 mm is used as a…
A:
Q: The pressure P in pounds per square foot, in a pipe varies over time. Every half-hour, the pressure…
A: Simple Harmonic Motion: In this type of motion, particle oscillate about its mean position. Any…
Q: A rubber band 20 cm long has a cross-sectional area of 0.04cm^2. What load (in dynes) will stretch…
A: Given data: The length of the rubber band is L = 20 cm. The cross-sectional area of the rubber band…
Q: The maximum height h of a mountain depends on the density of the rock the mountain is made out of ?ρ…
A:
Q: Four identical hollow cylindrical columns of mild steel support a big structure of mass 50,000 kg.…
A:
Q: A tensile stress is to applied along the long axis of a cylindrical brass rod that has a diameter of…
A:
Q: I Find the maximum at A. Take V- 5000N ↓ Imm 140 mm A shear stress & the shear stress 20mm 100mm I…
A:
Q: An elastic cube with side size a = 500mm is placed on two rigid walls and one rigid slab. A uniform…
A:
Q: In the Challenger Deep of the Marianas Trench, the depth of seawater is 10.9 km and the pressure is…
A:
Q: The figure shows the stress-strain curve for a material. The scale for the stress axis is set by s =…
A: Given, Stress, S=300×106N/m2 Strain, s=0.004 The young's modulus,…
Q: If the applied load is 49 kN, determine the new diameter of the specimen.
A: Given:- G = 28 Gpa diameter of specimen = 12.5mm Gauge length = 50 mm Given diagram:-…
Q: The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain.…
A: Given: εx=0 μεεy=350 μεγxy=210 μrad -45o≤θp≤+45o
Q: A 8-mm-thick rectangular alloy bar is subjected to a tensile load P by pins at A and B, as shown in…
A:
Q: Ex. 71: Calculate the work done in stretching a wire of diameter 1.2 mm and length 4 m by 0.2 m.…
A: To find-Work done in stretching a wire.Given-Diameter d=1.2 mmTherefore-r=0.6 mm=6×10-4 mL=4 ml=0.2…
Q: For the given state of stress, determine: (1) The principle stresses and the directions of the…
A: Solution:- 1). In the figure given we have: σx= 350…
Q: A cable used to lift heavy materials can resist breaking even under a load of 1 meganewtons. The…
A:
Q: Two parallel and opposing forces of each value (4000N) act tangentially on opposite sides of a cube…
A: Given: Force F=4000 N Side length L=25 cm=25×10-2 m Shear modulus S=80 GPa=80×109 Pa
Q: You have a piece of uniformly shaped 5.78 cm long yarn, the diameter of which you can neglect. If…
A: Given : L = 5.78 cm = 0.0578 m Q = 4.69 × 10-10 C
Q: A copper (shear modulus 4.2 x 1010 N/m²) cube, 0.450 m on a side, is subjected to two shearing…
A:
Q: For an infinitely long, constant-width estuary, the mean water depth is 20 m, and the tidal…
A: The depth of the water is given as, h=20 m The tidal elevation at the ocean end is given as,…
Q: The principal forces at a point p of an elastic body are o(¹)=50N/cm², o(2)=-50N/cm² and…
A: The first principal force is The second principal force is The third principal force is
Q: If the Junk modulus of Y is 160GPA and the shear modulus of elasticity is 0.25Y, what is the value…
A:
Q: Young's modulus for compression of human bone is approximately 9x10⁹ N/m^2. Assume that a femur has…
A: Given in question : Young's modulus (Y) = 9 x 109 N/m2 Stress (S) = 7.5 x 107 N/m2 Length of the…
Q: The true stress-strain behavior of a metal is given by otrue = K- (Etrue)", where Otrue is the true…
A: Given, σtrue=Kεtruen
Q: te=120 (2) 457 tレ Oa = 60 the figure (0,c=0), find the principal Q-For the plane stress case shown…
A: Given : A plane stress case.
Q: For the beam and loading shown, determine the maximum absolute value of bending moment and shear.
A: Draw the free-body diagram of the beam.
Q: Task 8. Consider a unit cube of an isotropic solid occupying the region 0≤ x ≤ 1, 0≤ y ≤ 1, 0≤ z <1.…
A: Volume of a cube is given byV=xyz, where x,y and z are length elements.For a unit cube,…
Q: The perimeter forming rate of the 45 ° jet shown in the figure is calculated when the strain rates…
A:
Q: Ex. 13: A cube of side 5 cm each whose upper face is displaced by 0.65 cm due to a force of 0.25 N.…
A: We need to compute-(i) Shearing stress=?(ii) Shearing strain=?(iii) Modulus of rigidity=?The data…
Q: 1) A ball of mass, m = 2.50 kg, floats on a pool of fluid, L-1.00 m wide. It is attached to supports…
A: As per question, a block of mass m=2.5kg, is connected with the two spring, length of the pool L=1.0…
Step by step
Solved in 3 steps