The strain energy due to volumetric strain (a) Is directly proportional to the volume (b) Is directly proportional to the square of exerted pressure (c) Is inversely proportional to Bulk modulus (d) All options are correct

The strain energy due to volumetric strain (a) Is directly proportional to the volume (b) Is directly proportional to the square of exerted pressure (c) Is inversely proportional to Bulk modulus (d) All options are correct

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.3P: Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2...

See similar textbooks

Related questions

Q: In design analysis, allowable stress for a material should not exceed the values within the ……

A: Factor of safety is defined as the ratio of yield stress to working stress. so the yield stress…

Q: 2. What refers to the stress in the material at the elastic limit? 3. What is the ratio of the…

A: Elastic limit is the limit by virtue of its material regain its original shape and size…

Q: The figure shows the state of stress on the element at a point on a member. Determine the stress…

A: Normal stress about x axis, Normal stress about y axis, Shear stress, Angle, To find: Stress…

Q: 2. A steel with E = 29 000 ksi with a rectangular cross-section is bent over a rigid mandrel with R…

Q: What are the s tress components, ojs terms of C, a and N?

Q: Determine stress value

A: This question is related with solid mechanics . In this question we are provided with value of…

Q: A steel bar 30 mm in diameter and 2 m long is encased in a shell of cast iron 5 mm thick. Compute…

Q: The deformation per unit length is called O a. Strain O b. Tensile stress O c. Shear stress O d.…

Concept explainers

Pressure and Stress

Question

The strain energy due to volumetric strain
(a) Is directly proportional to the volume
(b) Is directly proportional to the square of
exerted pressure
(c)
Is inversely proportional to Bulk modulus
(d) All options are correct

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
Kindly include the diagram. Handwritten solution recommended.
Discuss the principles of stress and deformation analysis for several kinds of stresses
What is the ratio of the strain energy in bar X to that in bar Y when the material of the two bars is the same? The cross-sectional areas are as indicated over the indicated lengths. 1/2 A/2 Bar X 1/2 Bar Y
Steel Stress-Strain diagram. Which of the following statements is NOT correct? Engineering stress is the stress computed using the original area and not the necking down area. The constant stress region is called the yield plateau or plastic range. The linear portion is also called the plastic range. The proportional limit, elastic limit, upper and lower yield points are very close to one another and are treated as a single point called the yield point.
!
Normal stress is calculated dividing the reaction by the cross-sectional area. Is this approach valid for any point of a structural member? Why or why not? To answer this question, consider the loading point, cross- sectional shape, etc.
5.
Discuss Stress-Strain Properties
Derive the expression for the stress transformation.
ProbleT = - An aluminum bar has diameter d = 40 mm, shear modulus of elasticity G = 27 GPa, and torque T = 300 N.m. (a) Determine the maximum shear, tensile, and compressive stresses in the bar, and show these stresses on sketches of properly oriented stress elements. (b) Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements. |d=40 mm T= 300 N-m
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).