The straight line A B having the following data : A (2, 2) , B (0,0)left of A. Distance between projectors = 6 cms. Required: 1- Draw (scalel:1) the ELEVATION & PLAN of the line and determine the following a- Its true length b- The coordinate of its traces H&V. c-its inclinations (a &ß)

Q: fx A C 1 Variable Value Units 2 diameter 3 m 3 height 5 m 4 volume m^3 3 The image above shows a…

A:

Q: A2.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A:

Q: 5m From the given figure. A stone wall is pulled by two tension rope at B and C. FB=240N, Fc=200N 5m…

A:

Q: Determine the mass of the counterweight necessary to launch a 7g clay ball 3 meters. A) Find…

A:

Q: an isometric For the objects shown in orthographic projection below, construct Use the box method to…

A: Given: Draw isometric view from given orthographic projections.

Q: Find the resultant vectors. This referes to Question 4 on the PDF v Horizontal 30N and Vertical 60N…

A:

Q: Determine the magnitude and coordinate direction angles of the resultant force. 0.75 m FAR = 250 N…

A: Given, FAC = 400 N FAB = 250 N

Q: Q3/ Find the angles and the distance for each plane, using by draw the following the table for each…

A:

Q: i have a question, please help The resultant describes the __________ of multiple ___________. The…

A: The question is given about addition of vector. We have fill the correct sequence.

Q: 3. On the drawing and produced part below, label the following terms: Datum feature symbol Datum…

A: Label the given terms.

Q: Now we will repeat the previous problem using the Cartesian method. Values: FA = 20 N FB = 30 N a =…

A: According to the question FA =20 N FB =30 N angle = 25 deg we need to find the resultant with the…

Q: Dr. Deduction has a peculiar penchant for using elaborate experimental se- tups and convoluted…

A: Since each element of the system is connected trough a single cord, the acceleration of each element…

Q: DIMENSION THE OBJECT SHOWN BELOW. NOTE THAT NOT ALL ORTHOGRAPHIC VIEWS WILL REQUIRE DIMEN- SIONS. DO…

A:

Q: Problem 1: Basic 2-D Construction In this exercise basic construction and edit commands will be…

A: Given DataThe length of the figure is 6.5 units.The height of the figure is 4.5 units.FindCreate the…

Q: The 3D view of an object is shown below. Use SolidWorks to model the objects. Dimensions are in mm.

A: Right hand side view

Q: b) A ship is moving relative to the water and you are given the following velocities: Magnitude…

A: According to the information we have a ship moving relative to the water with a velocity for…

Q: Values for dimensions on the figure are given in the following table. Note the figure may not be to…

A: (a) Write the given data. a=76.2 cmb=88.9 cmc=38.71 cmh=83.82 cm

Q: Required information A model of a person's arm is used for ergonomics studies. Distances are rAB =…

A:

Q: nswer with a few sentences or provide a sketch. w a) In rectangular coordinates the unit vectors…

A: In a rectangular coordinate the unit vector may or may not changes with time. In case of fluid the…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.