The steel rods (E = 200 GPa) support a 36 kN load P. Each of the rods AB and CD a 200 mm2 cross-sectional area and rod EF has 625 mm2 cross-sectional area. Determine (a) the change in length of rod EF, (b) the stress in each rod

Q: A Truck in which the pair of wheels at the rear side carries a load of 1.5 Tonnes on each axle box,…

A: Given: Maximum allowable stress: →τ=100 N/mm2 Load on each axle box: →P=1.5 tonns…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A:

Q: Member BC shown is subjected to a vertical force of 45 kN. Determine the position S of this force so…

A:

Q: The members of the truss shown below have a cross-sectional area of 10,000 mm2. Determine the…

A:

Q: For the clevis connection shown, the shear stress in the 0.21-in.-diameter bolt must be limited to…

A: Given: Let us consider the given data, Shear stress,  τ=39 ksi=39×103 Psi Bolt's diameter, d=0.21 in…

Q: 3. The frame supports the distributed load shown. Determine the state of stress acting at point E.…

A:

Q: The members of the truss shown below have a cross-sectional area of 10,000 mm-. Determine the…

A:

Q: 1. The steel system consists of rod CD, rod AB and a rigid bar AC. The diameter of rods CD and AB…

A:

Q: consider a specimen having a length L of 200 mm and diameter D of 5 mm subjected to a tensile = F of…

A:

Q: Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm…

A:

Q: Q3. The rod BC is made of steel having an allowable tensile stress of Gallow=160 MPa. Determine its…

A:

Q: A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine…

A: Given data, Di = 100 mm. Tensile load = P = 400 KN = 400000 N. Stress= σ = 120 MN/ m2 = 120 N/mm2…

Q: For the stress shown below, determine the cross-sectional areas of bars BE, BF and CF so that the…

A: For the stress shown below,Determine the cross-sectional areas of bars BE, BF and CF so that the…

Q: The 80-kg lamp is supported by two rods AB and BC as shown in Fig. 1-16a O If AB has a diameter of…

A: Given Weight of the lamp = 80 kg To find Stress of rod BC Stress of rod BA

Q: eter of wires AB and CB. The allowable tensile stress in each wire is 185 Mpa. 30

A:

Q: band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The interval diameter of the hoop…

A:

Q: Determine C 2.8 kN E=200 GPa the force in AD member. F. = ? AD rigid member 8x 6 in mm 8x 6 in mm A…

A: Let the force in forces in left and right member be FAB and FB . For equilibrium in X-direction -FX…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A:

Q: Please answer within 1 hour, thank you! The truss above is designed in such a way that all…

A:

Q: The steel system consists of rod CD, rod AB and a rigid bar AC. The diameter of rods CD and AB are…

A: Answer: (a) The normal stress in rod AB and CD are 78.5950 MPa and 49.7359 MPa respectively. (b) The…

Q: А В C

A:

Q: The homogenous bar that weighs 5000 lb is supported by a pin at C and a cable that runs from A to B…

A: Given data  Weight (W) = 5000 lb  dimaeter of cable (d) = 0.8 in To determine   Axial stress in the…

Q: - B А The value of toughness is measured the under point Point D to point A B. Zero to point D Point…

A: Dear student, as per the given options there is no correct answer. Please find the explanation…

Q: Q3- Determine the minimum dimeter dl and d2 for the two solid cylinders shown below. Cylinder AB and…

A:

Q: rod of length L having uniform cross-sectional area A is subjected to a tensile force P . If the…

A: Given: A rod of length L having uniform cross-sectional area A  is subjected to a tensile force P…

Q: Determine the largest weight W in kN that can be supported by the two wires AB and AC: The working…

A:

Q: A suspended date that's able to pivot from the top seperates two liquids. There is a stopper that…

A: Given, Gate height, h=0.5 m Since, the liquid on the right is twice as dense as liquid on the left.…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 33…

A:

Q: The rods CE (A = 130 mm²) and DF (A = 250 mm²) are attached to the rigid bar ABCD as shown. Knowing…

A:

Q: A steel bar having cross sectional area of 100 П mm² is subjected to a tensile force of 40 kN.…

A: The tensile force is The cross sectional area is

Q: Problem The truss is made from three pin-connected members. Determine the maximum average normal…

A:

Q: A crane is supported by two cables with a cross-sectional area of 3.04 cm2 each. Determine the…

A: A=3.04cm2 = 304mm2 Assume P=20KN , Mass of the boom = 450kg

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.