The steel beam has the cross section shown. The beam length is L = 5.0 m, and the cross-sectional dimensions are d = 320 mm, bf = 210 mm, tf = 13 mm, and tw = 10 mm. Calculate the largest intensity of distributed load w0 that can be supported by this beam if the allowable bending stress is 205 MPa

Q: Question 4 • h₁-100mm • h-120mm • t=5mm • b-75mm N t- An I beam is subjected to an internal shear…

A:

Q: A steel rod of diameter 10 mm carries an axial load of 10 kN. Consider the modulus of elasticity and…

A:

Q: The cross-section of a composite beam made of aluminium and steel is shown in the figure. The moduli…

A: Given Es=200GPa EA=75GPa Maximum stress in aluminium=50MPa

Q: For the state of stress shown, determine (a) the principal stresses, (b) the maximum in-shear…

A:

Q: 5. A metallic top-hat stringer reinforced wing skin (function of the material A=150) has a width of…

A: The function of the material = 150Width =1.5 mUnsupported length =0.5 mApplied compressive load =120…

Q: 3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a…

A:

Q: The limit of proportionality in the material of a structural steel member, when subjected to simple…

A: Given data- A structural steel member- Simple tension-σy=280 N/mm2Principal stress-σ1=122 N/mm2…

Q: How to make a effective stiffness matrix for this figure? The bending stiffness is 2EI A B.

A: In the diagram  there are 3 global degree of freedom Q1,Q2,Q3 , Calculate the developing stiffness…

Q: The cross-section of a composite beam made of aluminium and steel is shown in the figure. The moduli…

A:

Q: small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this…

A: Calculating the reactions:

Q: What is the stress at the section x - x. for the bar ABCD with uniform cross-section 1000 mm²? с A…

A:

Q: 1) The simply supported beam with the cross-section as shown in the figure supports the loads as…

A: Given: Flexural stress = 100 Mpa Determine t = ?

Q: The composite beam shown in the figure is simply supported and carries a total uniform load of 40…

A: In composite beam, bending strain diagram is linear and strain compatibility conditions is used to…

Q: 160 kN LLET --3m-> -6m 400 kN 6m X 40 mm 200 mm 100 mm 20 mm

A:

Q: The A-36 steel column is encased in high-strength concrete as shown. If an axial force of 60 kip is…

A:

Q: Given the properties of the section below: width = 1000 mm thickness = 392 mm concrete cover to bar…

A: Strain is defined as the amount of deformation (stretch or compression) generated by a stress…

Q: SITUATION 31 A solid mild-steel is rigidly clamped at one end and subjected to an applied torque T =…

A:

Q: For the continuous beam shown in Figure 1, draw the internal force diagrams. You must accompany your…

A: Given Data:

Q: 5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in the given figure.…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: 3. A 16 mm steel bar AB and a 25 mm steel bar BC support a load P = 7,500 N as shown. If E= 200 GPa,…

A:

Q: Using critical stress to show the shear effect is negligible in solid steel simply supported column…

A: Structural engineers get a genuine pride when a venture is done, regardless of whether it is a high…

Q: A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.…

A:

Q: For the state stress shown in figure below, determine the principle stresses and the maximum…

A:

Q: A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall…

A: Given:- 5.0 m simple beamPu=45kNwu=44.24kN/mspan=5.0mTo find:-stress in steel

Q: Q4. A steel cantilever beam is of circular cross-section is subjected to a transverse load at its…

A: Solution Given that Ultimate strength= 600 MPa Yield strength= 360 MPa Endurance limit= 300 MPa…

Q: Q1) A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of Syr =…

A: step 1-

Q: A small aluminum alloy [E = 62 GPa] tee shape is used as a simply supported beam as shown. For this…

A:

Q: A beam having the cross section shown is subjected to a couple Mo acting in a vertical plane.…

A: Given, Iy = Iz = b436 Iyz = b472 σ = 103 MPa

Q: arning Goal: me member shown is subjected to a compressive ress in the x direction of a = 400 ksi…

A:

Q: 2. A cantilever beam of 1.0 m long is subjected to a concentrated load Po at its free end. Determine…

A: given: allowable  tensile stress=180MPa allowable compressive stress=140MPa allowable shear…

Q: given cross-section, given the following conditions: • tensile stress should not exceed 100 ksi •…

A:

Q: hat have an outside diameter of 135 mm and a wall thickness of 9 mm. Determine the normal stress in…

A: From a given question it is required to calculate stresses in each member of truss.

Q: The cross-section of a pretensioned prestressed concrete beam is shown in figure. The reinforcement…

A:

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.