The state of plane stress at a point is represented by the element shown in Figure Q1. Construct a Mohr Circle to determine a) the principal plane and the principle stresses, ) the maximum in-plane shear stress and the associated average normal stress, and ) the state of stress at the point on another element oriented 25° clockwise from the position shown. 1) Show the orientation of the element stresses on an appropriate sketch for a), b) and c)

The state of plane stress at a point is represented by the element shown in Figure Q1. Construct a Mohr Circle to determine a) the principal plane and the principle stresses, ) the maximum in-plane shear stress and the associated average normal stress, and ) the state of stress at the point on another element oriented 25° clockwise from the position shown. 1) Show the orientation of the element stresses on an appropriate sketch for a), b) and c)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2) The state of stesss at a point in a body relative to the xyz coordinate system is: 2 3 -5 [o]= 3 2 kpsi 6. %3D -5 2 -4 a) Determine the principle stresses and the direction cosines corresponding to each principle stress. b) Draw the 3D Mohr's circles. c) Determine the maximum shear stress. d) Find the orientation of the plane containing the maximum shear stress relative to the original axis system 3) For the stress tensor in problem 2: a) Determine the normal and shear stress on a surface intersecting a plane defined by 3 points (0,0,0); (2,-1,3); (-2,0,1) b) Give the magnitudes of these stresses and the direction cosines defining their directions.
Angle 1 Tyx Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. c) Using a Mohr circle, determine and draw the maximum stress block of the in-plane maximum shear and principle stresses. d) Determine the stresses and orientation of the stress block where the normal stress is zero. Make use of the stress transformation equations. e) Determine the values of absolute maximum shear stress and corresponding normal stress.
B) The Figure shows Mohr's circle for a point in a physical object that is subjected to plane stresses. 1) Determine the stresses ox, oy, and txy, and show them on a stress element. 2) Determine the principal stresses and the maximum in-plane shear stress acting at the point. O 1 grid square= 7 MPa O
The reference state of stress shown in the element sketch below results in the Mohr’s circle plot indicated. For this element, as described below, determine:a)The principal stresses.b)The principal directions (angles to the principal planes).c)The maximum in-plane shear stress.d)Is the maximum in-plane shear stress the absolute maximum shear stress?
The state of stress at a given point is given in the following figure. Use Mohr’s circle to find: a) The principal stresses b) The maximum in-plane shear stresses. For both cases you must draw a rotated element including all stresses and the angle of rotation. You must draw a properly labeled Mohr’s circle.
For the state of plane stress, stress components are shown on the element in Figure Question 1: a) Draw Mohr's circle b) Determine the principal planes and the principal stresses c) The stress components exerted on the element obtained by rotating the given element counterclockwise through 30°. y| 60 MPa x 100 MPa 48 MPa
The stress components acting on an infinitesimal element extracted from a plate subjected to the plane stress state are given in the figure. a) Find the principal normal stresses and their directions and show them on the oriented element. b) Draw the Mohr circle schematically and indicate the points on the given element on this circle. 60MPA A 30° 60° 40MPA 80MPA
1) Figure 1 shows an element with stresses. Angle 1 Tyx Txy Tyx Figure 1 Point C)- x-direction stress 60MPA(compression), y-direction stress 40MPA(compression), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1. 50° Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. んや

For a point under a plane state of stress, the stresses on the vertical and horizontal planes are shown in the figure below. 100 MPa 48° 80 MPa 60 MPa Using only the stress transformation EQUATIONS, determine the following: a) The normal stresses on the plane oriented along plane a-b. o, = b) The shear stress on the plane oriented along plane a-b Ty'= c) The locations of the principal planes (express your answers as angles made by the principal planes with respect to the horizontal) Op2= d) The principal stresses Op1= Op2= e) The maximum in-plane shear stress Tmaxip= Show the results of both stresses in plane a-b and principal planes on a sketch of the plane on which these stresses act.
Given: The infinitesimal “happy-little-cube™" with stresses shown. Determine: Draw Mohr's circle for the stress shown, label a) max and min principal stresses, b) max shear stress, c) center and d) plot the stress state shown on the circle 12 ksi Show all work. Do not calculate any angles! 6 ksi
A plane stress state is given as follows (50MP in the bottom right corner denotes the shear component, and others denote the normal components). 1) Please draw the Mohr's circle of this plane stress state. Indicate the center of the circle, the radius of the circle, and the point that corresponds to x-plane (the normal of the plane is x axis) 2) Determine the principal stresses and directions of this stress state using Mohr's circle. 3) Draw the stress element to show maximum shear stress 71, T2, and the corresponding normal stress. 75 MPa 50 MPa 50 MPa
(b) Mohr's circle, invented by Christian Otto Mohr, is a graphical representation of the transformation law for the stress system. Use Mohr's circle to determine the stresses on an element inclined at 30° clockwise to the state of plane stress system as shown in Figure 1 and show the corresponding stress elements. Q2 (a) It is important im 80 MPa 50 MPa Ľ 50 MPa Figure 1 80 MPa 25 MPa