The stagnation chamber of a wind tunnel is connected to a high pressure air bottle farm which is outside the laboratory building. The two are connected by a long pipe which has a inside diameter of 4 inches. If the static pressure ratio between the bottle farm and the stagnation chamber is 10 and the bottle farm static pressure is 100 atm, how long can the pipe be without choking and what is the change in entropy? Assume adiabatic,subsonic, one-dimensional flow with a friction coefficient of 0.005.

The stagnation chamber of a wind tunnel is connected to a high pressure air bottle farm which is outside the laboratory building. The two are connected by a long pipe which has a inside diameter of 4 inches. If the static pressure ratio between the bottle farm and the stagnation chamber is 10 and the bottle farm static pressure is 100 atm, how long can the pipe be without choking and what is the change in entropy? Assume adiabatic,subsonic, one-dimensional flow with a friction coefficient of 0.005.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

multi-stage high –pressure steam turbine is supplied with steam at a stagnation pressure of 7 MPa and a stagnation temperature of 5000C. The corresponding specific enthalpy is 3410kJ.kg. The steam exhaust from the turbine at a stagnation pressure of 0.7 MPa abs., the steam having been in a super-heated condition throughout the expansion. It can be assumed that the steam behaves like a perfect gas over the range of the expansion and that ᵞ = 1.3. Given that the turbine flow process has a small-stage efficiency of 0.82, determine (1) the temperature and specific volume at the end of the expansion; (2) the re-heat factor. The specific volume of superheated steam is represented by pv=0.231(h-1943), where “p” is in kPa, v is in m3/kg and “h” is in kJ/kg.
Need step by step explanation
Air flows through a constant area combustion chamber that has a diameter of 0.15 m and a length 5 m. The inlet stagnation temperature is 335 K, the inlet stagnation pressure is 1.4 MPa, and the inlet Mach number is 0.55. Find the maximum rate at which heat can be added to the flow. Neglect the effects of friction.
Show that the point of maximum entropy on the Fanno line for the adiabatic steady flow of a fluid in a duct corresponds to the sonic velocity, Ma = 1.
I need the answer as soon as possible
The air temperature is 288K and the pressure is 1 atm upstream of a shock wave; After the passing through the shock wave, the temperature of the air is 690K and the pressure is 8.656 atm. Calculate the change in a) enthalpy b) internal energy, and c) entropy across the wave. Assume R = 0.287 kJ/kg⋅K and ? = 1.4
Compute the change in specific entropy when helium, initially at a temper-ature of 273 K and a pressure of 100 kPa, undergoes the following processes: a.An isochoric process with final pressure 250 kPa b.By computing the change in specific entropy, determine whether it is possible foran adiabatic process to bring the gas to a final temperature of 200 K and a densityof 0.3 kg/m3. If not, why not? And if so, how could it be done?
A large vessel contains compressed air at To = 350 K and Po = 2 bar. A converging-diverging nozzle is attached to the vessel to discharge air. The throat area of the nozzle is 200 cm2. At the exit, the pressure is 20 kPa and the flow is supersonic. Answer the followings:
Air flows through a converging-diverging (c-d) nozzle. It is supplied from a large air reservoir in which the temperature is 446 K and the pressure is 190 kPa. The velocity and the cross-sectional area at the nozzle exit are 594 m/s and 0.0005 m^2, respectively. Find the followings: Mach number at exit is Area of the throat is The mass flow rate of air is The exit temperature is The exit pressure is
Draw the p-V and T-s diagram
How do I find reservoir pressure given the exit-to-throat area ratio of a supersonic nozzle and a Pitot tube measurement from the test section.
1)Air is supplied to a converging nozzle from a large reservoir where the temperature and pressure are 400 Kand 150 kPa, respectively. At a certain cross-section where the area Is 0.01 m2, the pressure and velocity are 100 kPa and 120 ms·', respectively. Assuming adiabatic flow, find the Mach number at this cross-section and determine the mass flow rate. 2) Helium flows adiabatically through a duct. At some section, where the area is 0.02 m2, the velocity is 500 ms·1 and the pressure is 100 kPa. Find the Mach number at the given section, and determine the mass flow rate if the stagnation temperature is 300 K