b) Air flows through a cylindrical duct at a rate of 2.3 kg/s. Friction between air and the duct and friction within air can be neglected. The diameter of the duct is 10cm and the air temperature and pressure at the inlet are T₁ 450 K and P₁ = 200 kPa. If the Mach number at the exit is Ma2 1, determine the rate of heat transfer and the pressure difference across the duct. The constant pressure specific heat of air is Cp 1.005 kJ/kg.K. The gas constant of air is R = 0.287 kJ/kg-K and assume k = 1.4.

b) Air flows through a cylindrical duct at a rate of 2.3 kg/s. Friction between air and the duct and friction within air can be neglected. The diameter of the duct is 10cm and the air temperature and pressure at the inlet are T₁ 450 K and P₁ = 200 kPa. If the Mach number at the exit is Ma2 1, determine the rate of heat transfer and the pressure difference across the duct. The constant pressure specific heat of air is Cp 1.005 kJ/kg.K. The gas constant of air is R = 0.287 kJ/kg-K and assume k = 1.4.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
Do not give answer in image and hand writing
An ideal gas passes a diffuser. At the diffuser inlet, the temperature is T1 = 350.00 K, the pressure P1 = 100.00 kPa, the velocity V1 = 200.00 m/s, and the inlet area A1 = 0.30 m2. At the exit, the velocity is very small. The specific heat of the ideal gas at the constant pressure is cp = 1.0050 kJ/(kg·K). The gas constant is R = 0.2870 kPa·m3/(kg·K). Determine the enthalpy per unit mass at the inlet, h1__________(kJ/kg)
I need the answer as soon as possible
stagi 900 kPa 1- Air enters a compressor for a mass flow rate of 0.04 kg/s. at a stagnation temperature 358 K. Assuming the AIR compression process to be isentropic, determine the power 0.04 kg/s require. 100 kPa stagnation
20.3 cm diam 2.44 m 1.22 m Water Air at 105 kPa and 37°C flows upward through a 6-cm-diameter inclined duct at a rate of Q (L/s). The density of air at this temperature and pressure is 1.10 Kg/m³. The duct diameter is then reduced to 4 cm through a reducer. The pressure change across the reducer is measured by a water Air manometer. The elevation difference between the two points on the pipe where the two arms of the manometer are attached is 0.20 m. Determine the differential height between the fluid levels of the two arms of the manometer. Q (L/s) 90
(1) Given the working form of the Bernoulli equation as v2 + gz + dW - F dm Where s is the friction heating per unit mass dQ F = Au dm Given also that friction heating in laminar flow of Newtonian fluids in circular pipes is given as -AP F = = -gAz = Q Ax µ 128 Ax is change in the x-direction. A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m'. The flow rate is 10* m³ / s. What is the viscosity of the fluid? Typical capillary viscometer
thank you
Argon is accelerated in a nozzle from 32 m/s at 666 K to 441 m/s and 196 kPa. If the heat loss is equal to 5.1 kJ/kg, determine the gas temperature at outlet in K to 1 decimal place. Take the gas constant as 0.2 (kPa m3)/(kg K) and assume constant specific heats cp=0.5 kJ/(kg K) and cv=0.3 kJ/(kg K).
The static and stagnation pressures of a fluid in a pipe are measured by a piezometer and a pitot tube to be 200 kPa and 220 kPa, respectively. If the density of the fluid is 600 kg/m^3, the velocity (in m/s) of the fluid is ?"
A water is flowing through the duct having daimeter 15 cm and length 15 m. The inlet temperature of water is 100 °C & exit temperature is 5 °C respectively. Calculate the mass flow rate of water through the duct in mol/sec by considering heat transfer due to convection. Individual heat transfer coefficent is 15 w/m2K.
In mechanical fluid