The springs on the rope assembly are originally unstretched when theta = 0°. Determine the tension in each rope when F = 400 N. Neglect the size of the pulleys at B and D.

Q: The uniform plank ABC weighs 40 kg. It is supported by a pin at A and a cable that runs around the…

A:

Q: Problem 2. Consider the frame loaded as shown. If the reaction force at the roller at F is 250N,…

A:

Q: 4. Determine the tension in the cable at B, given that the uniform cylinder weighs 350 lb. Neglect…

A:

Q: Q3 - The uniform bar OC of length L and mass ( m ) pivots freely about a horizontal axis through O.…

A:

Q: Q6\ If the tension in the spring is 600, the vertical component of the pin reaction at B is:

A: Consider the free body diagram of the EB and AC as shown below.

Q: A 415 kg safe is hanging from the apparatus below.  Determine the tension in the cable.  Dimension…

A:

Q: Find the tension in leg AC of the cable if the sag, h = 4'. 3' h

A:

Q: in the pulley system and the diagram above, assume that the bearings at oh and C are properly…

A:

Q: The man attempts to pull down the tree using the cable and small pulley arrangement shown. If the…

A: Consider following given figure.Tension in cable AB = Assume pulley to be frictionless, hence…

Q: The 6-m pole ABC is acted upon by a 460-N force, P, as shown in the figure. The pole is held by a…

A:

Q: Determine the tension in the horizontal cable

A: Given data as per the question weight =200 kg Considering the fig. and forces applied to it…

Q: A uniform steel ring 600 mm in diameter has a mass of 100 kg and is supported by three cables, each…

A:

Q: Determine the support reactions and draw the SFD and BMD for the following frame. 5 kNim

A:

Q: Determine the maximum weight of the bucket that the wire system can support so that no single wire…

A:

Q: F2 F1 a 0.4 m- - 0.4 m- 0.24 m

A:

Q: Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power…

A:

Q: Determine the forces in each cable if P = 10kN.

A:

Q: The weight W = 6kN hangs from the cable which passes over the pulley at F. Neglecting the weights of…

A:

Q: Knowing that F = 370 N and 0 = 15°, determine the tension in the spring and reactions at A if the…

A: The force F=370 NLength of the arm AD=400 mm=0.4 mLength of the arm AB=300 mm=0.3 mAngle between the…

Q: THE 600 lb CRATE IS SUPPORTED BY THE THREE CABLES. FIND THE TENSION IN EACH CABL

A:

Q: A 10 m y 16 kN/m 10 m B T 2 m -X

A: w0= 16 kN/mL= 10 mLtotal= 10+10= 20 mh= 2m

Q: 300 mm 250 mm 200 mm 65 N 80 mm A 80 N 150 mm B -50 N

A:

Q: magnitude of the vertical reaction force developed at the point B

A: Given; Two steel truss members, AC and BC, each having cross-sectional area=100 mm2It is subjected…

Q: The horizontal force P is applied to the handle of the puller. Determine the resulting tension T in…

A: Given Data The distance from the load to the point B is: 24 in The angle of the puller is: 40° The…

Q: Determine the tension in the cable at B, given that the uniform cylinder weighs 350 lb. Neglect…

A: Draw the free body diagram of the cylinder. OC=3 ftcos 40°OC=2.3 ft ED=3 ftsin 50°ED=2.3 ft

Q: Q3 - The uniform bar OC of length L and mass (m ) pivots freely about a horizontal axis through O.…

A: Given data: The angle between OAC is θ=45° The length of the bar is L

Q: During crash testing of an automobile, the lap and shoulder seat belts develop tensions of F = 260…

A:

Q: ROLLER BACKSTRAY ROLLER C60 11.5M BACKSTRAY ABUTMENT ÁBUTMENT 10 M

A: Given: The value of the uniformly distributed load is 700 N/m.

Q: Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power…

A: Draw the free body diagram of the shaft as in Figure (1).