The spring has an unstretched length of 0.4m and a stiffness of 200N/m. The 3 kg slider and attached spring are released from rest at A and move in the vertical plane. (a) Compute the change in elastic potential energy from A to B. (b) Compute the change in gravitational potential energy from A to B. (c) Compute the velocity of the slider as it reaches B in the absence of friction.

Q: system that has characteristics of a spring with a constant 45 lbs / ft. If the car has an initial…

A: In the question, the friction is given to be zero. Thus there will no loss of energy possessed by…

Q: of the slot on the cylind e the cylinder is in cont and slot at any instant. neces to om

A: Function relating the radius and angle made r= 0.6 θ ---- (1) Substitute π rad for θ in equationr=…

Q: The force P is applied to the 53-kg block when it is at rest. Determine the magnitude and direction…

A: Given data as per the question mass of block =53 kgμs=0.24μk=0.19

Q: The slotted arm OA rotates about a fixed axis through O. At the instant under consideration, 0 =…

A:

Q: The free-body diagram for the slider is shown. Solve for the forces N and F. F N mg Answers: F = i…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: 3) A 60 kg block is pulled by a force of F = 500 N as shown. Ifthe block starts its motion from…

A: In vertical direction          N = Wcos30-Fsin30=60×10cos30-500sin30=247 N Where,          N =…

Q: If the system comes to momentary rest at 0 = 36º, determine spring constant k. For the value k=110…

A: Given: b=0.4 m m= 4 kgTo determine:Spring constant k when θ=36°Final velocity when θ=20° and k=110…

Q: B 3 m -6 m- A hass at G. Initially, at take-off, the engines provide a thrust

A: 2T=2kN.. T'=1.7kN mass of aircraft=25000kg

Q: k Force Cart I Cart 2 Sensor Mass = M Mass = 3.5M The figure above shows second experimental setup.…

A: After releasing from spring the cart 1 is free to move with some velocity and when it collides with…

Q: There is a 3,2kg slider ring is going down from the rest position A and slides in frictionless guide…

A: Calculate the potential energy of the slider at A considering B as datum surface. UA=mghA Here, UA…

Q: Write all the steps with free body diagrams as well please and thank you

A:

Q: The force Pis applied to the 57-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: The system is released from rest with the cable taut. For the friction coefficients us = 0.35 and H…

A:

Q: 4. The Block with a mass of 4-Kg is hung with a spring. The stiffness constant of the spring K = 10…

A: Given data: The force applied, F=100 N. The mass of the block, m = 4 kg. The spring constant, k=10…

Q: The motor is towing the crate that has a mass of mc= 1000 kg, and rests on the flat surface. It…

A: Given: The tension equation, T = 500t5/2 The mass of crate, m = 1000 kg The coefficient of static…

Q: Q4/ Assuming frictionless motion, compute the force exerted by the arm OA on the cylinder B when 0=…

A:

Q: The 3 kg block is initially at rest and pressed against a spring so as to compress it at point A.…

A:

Q: If the given system is released from rest in the position shown, calculate the velocity of B when it…

A:

Q: How to apply energy equation here . please include diagram. Don't use Artificial intelligence tools.

A: Step 1: Step 2: Step 3: Step 4:

Q: The 0.5 kg ball of negligible size is fired up the smooth vertical circular track using the spring…

A: m=mass of the ball= 0.5 kg ;θ=angle of ball from which ball rotate in circular path ;R=radius of…

Q: The 10 kg block A is on an inclined plane with 0 = 30° as shown in the figure below. The block is…

A:

Q: Q4 ] Q4. The 200-kg crate rests on the ground for which the coefficients of static and kinetic…

A:

Q: it is embedded into the wooden block. Which of the following is the maximum displacement of the…

A:

Q: Packages having a mass of 4-kg are delivered from a conveyor to a ramp with a velocity of v = 0.8…

A: Given data: The mass of the package is m=4 kg The initial velocity of the package is v0=0.8 ms The…

Q: Р.3) A collar of mass m = 2 kg is constrained %3D to move in the vertical plane along a rough rod of…

A: Consider the free body diagram as shown below for the collar.

Q: A 25 - lb block-on-a-slope (0 = 30°) mechanism has been arranged in the Dynamics lab so that at the…

A:

Q: Now the blocks with the same masses are big enough to touch each other, and the sides of the string…

A:

Q: The collar with mass of 0.6 kg is released from rest at position A and travels down the smooth…

A:

Q: Determine the force Prequired that will give the system of bodies in figure shown, a velocity of 3…

A:

Q: The blocks A and B shown in the figure are originally at rest, and all contact surfaces are…

A: mA=Mass of Block A=5 kgmB=Mass of Block B=3 kg

Q: The "flying car" is a ride at an amusement park which consists of a car having wheels that roll…

A: Given Data: Constant speed of the track vt=3 ms The radius of the circular path R=9.8 m The total…

Q: Show details of your solution for the problems below including FBDS when dealing with forces. 1) A…

A: Write down the given value using suitable variables. Here m signifies collar mass, vA signifies…

Q: Q4/ Assuming the car has no dependence on friction with the road, determine the speed u of the car.…

A: r = 365 m u = 0.8

Q: The harmonic excitation means that there is external force with any form. Select one: O True False

A: Given:

Q: The two blocks shown are originally at rest. Neglecting the masses of determine the tension in the…

A:

Q: Q3: The 2000 kg truck is starting from rest with a constant acceleration, and after 15 s reaches a…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.